White Westinghouse Refrigerator Parts

A single replacement screw used to secure appliance panels, brackets, or small components — restores proper fastening and reduces noise from loose parts. Simple, direct replacement when an original screw is missing or damaged. What it does:

• Fastens panels, trim, brackets or internal components to keep parts aligned and secure.
• Stops rattling, vibration or loose-panel movement caused by a missing or stripped screw.
• Provides the correct fit when replacing a lost or damaged original fastener.
• Intended for use where the OEM screw specification matches the appliance requirement.

• Disconnect power or unplug the appliance before accessing internal parts to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; hand-start threads before final tightening.
• Tighten until snug—do not overtighten, which can strip threads or crack plastic panels.
• Replace with an identical screw (head style, length, and thread) for proper fit and safety.

A replacement corner cabinet trim that restores the finished edge on the appliance cabinet and hides gaps for a cleaner look. Helps maintain the cabinet appearance and prevents debris buildup at the corner. What it does:

• Replaces a cracked, broken, or missing corner trim piece to restore the cabinet edge
• Covers gaps where two cabinet panels meet to improve appearance
• Helps reduce dirt and moisture accumulation in the corner area
• Stops rattling or catching caused by a damaged trim

• Service is generally simple; remove any nearby shelving or panels for access
• Fastens with the factory clip or screw method used on the model—retain original hardware and check alignment before final fastening
• Disconnect power to the appliance if needed to access fasteners near electrical components
• Wear gloves to protect hands from sharp sheet-metal edges during installation

This control box is the refrigerator's electronic control board that regulates key functions like temperature control, defrost cycles and user interface responses. Replacing a faulty board restores consistent operation and control of affected systems. What it does:

• Monitors and controls compressor and fan operation to maintain set temperatures
• Manages timed defrost cycles and related heater/relay functions
• Interprets user inputs from the control panel and sends commands to components
• Helps resolve symptoms such as unresponsive controls, incorrect temperature display, or irregular cooling cycles

• One control box (electronic control board)

• Disconnect power to the appliance before attempting service to avoid shock or damage
• Handle the board by its edges and avoid touching circuitry; use ESD precautions if available
• Verify connectors and harness routing match the replacement before fastening

This control box wiring harness routes power and signals between the appliance control board and other components to restore reliable control operation and electrical connectivity. It helps resolve intermittent controls and lost function caused by damaged wiring. What it does:

• Connects the control board to switches, sensors and motors to enable normal control functions.
• Replaces damaged or frayed wiring that can cause intermittent operation or unresponsive controls.
• Addresses symptoms such as control panel not responding, random shutdowns, or error codes tied to wiring faults.
• Restores proper signal and power routing when connector damage or wire breaks interrupt circuits.

• Disconnect all power to the appliance before beginning any service.
• Compare the new harness to the original and follow factory connector positions and routing to avoid pin miswiring or chafing.
• Handle connectors gently and ensure all terminals fully seat; inspect mating connectors for damage before reconnecting.

This replacement screw features a #10-32 machine thread and 3/4-inch length to securely fasten brackets, panels, and other components. Restore a tight, rattle-free fit by replacing missing or stripped hardware during repairs or reassembly. What it does:

• Secures panels, brackets, trim, and other mounted parts
• Replaces missing, rusted, or stripped screws that no longer hold
• Helps reduce vibration and rattling from loose components
• Maintains proper alignment and stability after service

• One screw (#10-32 x 3/4)

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the old screw and inspect receiving threads for damage
• Start by hand to avoid cross-threading; use the correct driver and do not overtighten (especially into plastic)

• Thread: #10-32 (machine)
• Length: 3/4 inch

This is a push on John Guess design elbow used to connect two 5/16" plastic lines together.

Black

A single replacement mounting screw used to secure appliance panels and components. Restores proper fit and prevents rattling or loose parts so trims and panels stay aligned during normal use. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Replaces worn, stripped or missing screws that cause loose or rattling parts
• Helps restore secure alignment for doors and access panels
• Works where the OEM lists a basic machine/fastener screw

• Disconnect power and water before beginning any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread by hand to start, then tighten until snug—do not overtighten
• Keep small parts away from children and pets during installation

This flat metal washer provides a durable spacer and load-distributing surface for a matching fastener, helping secure assemblies and reduce wear. It's a small but essential hardware piece for routine repairs and reassembly. What it does:

• Distributes fastening load to protect softer materials and prevent pull-through
• Creates a smooth bearing surface for nuts and bolts to seat evenly
• Helps reduce vibration and loosening in moving assemblies
• Commonly used on panels, brackets, and mounting hardware where a flush fit is needed

• One flat metal washer as shown

• Disconnect power and water (if applicable) and access the assembly before replacing hardware
• Use the matching bolt/nut size and washer ID/OD for correct fit; do not force oversized fasteners
• Hand-start fasteners to avoid cross-threading, then tighten to the equipment manufacturer's spec
• Keep small parts secure during disassembly to avoid loss or damage

This replacement cover protects internal components and provides a finished appearance for the appliance. It restores a secure access panel to help keep wiring and controls shielded from dust and accidental contact. What it does

• Shields controls, wiring, and internal components from debris and incidental contact
• Helps maintain a finished exterior appearance after repair
• Prevents loose openings that can let in dust or small objects
• Commonly replaced when cracked, broken, warped, or missing mounting tabs

• One cover

• Disconnect power (and water, if applicable) before servicing the appliance
• Handle carefully to avoid damaging mounting tabs or clips during removal/installation
• Use appropriate hand tools; avoid overtightening fasteners that can crack the part

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

This hinge bearing supports the refrigerator door pivot, reducing friction and helping the door open and close smoothly while maintaining proper alignment. Replacing a worn bearing restores smoother movement and helps reduce sagging or noise. What it does:

• Provides a low-friction pivot surface for the refrigerator door hinge.
• Helps maintain proper door alignment so the gasket seals correctly.
• Reduces hinge noise, squeaks and wobble caused by worn bearings.
• Common symptom fixes: door sagging, uneven closing, or noisy hinge movement.

• Disconnect power to the appliance before beginning any repair; turn off water if working near an ice/water dispenser.
• Remove or support the door and contents to prevent damage—doors can be heavy and require two people.
• Replace the bearing following the manufacturer's instructions; keep fasteners and hinge pins in their original order.
• After installation, check door alignment and gasket seal; tighten mounting screws as needed.

This defrost heater melts frost and ice from the refrigerator evaporator so the cooling system runs efficiently and food stays properly chilled. It restores normal auto-defrost operation when the original heater has failed. What it does:

• Heats the evaporator coil during the defrost cycle to remove frost buildup
• Helps maintain consistent cooling by preventing ice that can block airflow
• Common symptom: visible frost or ice buildup on the evaporator or inside the freezer
• Common symptom: reduced cooling performance or longer run times between cycles

• Always disconnect power to the appliance before replacing the heater to avoid shock
• Access typically requires removing the evaporator cover inside the freezer
• Inspect and replace any damaged clips, mounts, or wiring; harness connections are secure
• Test the heater for continuity (and check associated thermostat/thermistor) before final reassembly

This water inlet tube routes household water from the supply to the fridge's internal water system, helping deliver water to the dispenser and ice maker without leaks. Durable tubing replaces cracked or kinked lines to restore proper flow. What it does:

• Directs water from the supply valve to the refrigerator's internal water components.
• Replaces cracked, split, or kinked tubing that can cause leaks or low flow.
• Helps restore water flow to the dispenser and ice maker when the original line is damaged.
• Provides a secure, leak-resistant path when installed with proper fittings or clamps.

• One water inlet tube.

• Always disconnect power and shut off the water supply before replacing the tube.
• Drain and relieve pressure from the water line before disconnecting fittings to avoid spills.
• Use the correct OEM clamps or fittings and inspect connectors for wear; replace clamps if damaged.
• Tighten fittings securely but avoid over-tightening plastic fittings to prevent cracking.

This left-side meat pan rail block secures the meat pan/drawer slide in place so the drawer opens and closes smoothly. It replaces a worn or broken support to restore proper alignment and prevent the drawer from sagging or catching. What it does:

• Supports the left end of the meat pan/crisper drawer rail for stable sliding action
• Prevents the drawer from tilting, binding, or falling out when loading
• Replaces cracked, worn, or missing blocks that cause noisy or uneven drawer movement
• Keeps the drawer aligned for proper sealing and reliable operation

• Disconnect power to the appliance before servicing to avoid injury.
• Remove the meat pan/drawer per the appliance guide to access the rail block.
• Snap or screw the block into the rail per OEM alignment; do not force parts.
• If hardware is damaged or additional guides are worn, inspect adjacent components and replace as needed.

Left side.