White Westinghouse Refrigerator Parts

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Replacement shelf assembly for the freezer compartment restores a sturdy, level surface for food storage and organization. Replace a damaged or missing shelf to recover capacity, maintain proper spacing, and keep items from shifting.

• Creates a rigid support surface for items in the freezer section
• Maintains intended storage layout and airflow when installed in the correct position
• Replaces a bent, broken, rusted, or missing shelf
• Helps prevent tipping and overcrowding that can damage contents

• Unplug the appliance and wear gloves for safety.
• Remove or relocate food; slide or lift the old shelf out of its supports.
• Align the new shelf with the rails or tabs and fully seat it.
• Verify the shelf is level and secure before loading.

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This shelf and trim assembly replaces a damaged or worn refrigerator shelf trim to restore a secure shelf edge and improve storage stability. It provides the finished trim piece that retains items and keeps the shelf seated correctly. What it does:

• Replaces cracked, chipped, or missing shelf trim so food and containers stay securely on the shelf
• Restores the shelf edge that helps prevent items from sliding off when opening the door
• Re-establishes a proper fit between the shelf and cabinet for stable storage
• Helps maintain the refrigerator's interior appearance by replacing worn trim

• One shelf and trim assembly

• High-level replacement only — remove food and shelves before installing
• Use basic hand tools; avoid overtightening to prevent cracking the trim
• If the shelf is damaged, replace the shelf and trim together for best fit
• Disconnect power only if service requires accessing electrical components

This lower front grille/kickplate replaces a damaged or missing kickplate to restore your appliance's appearance and protect the lower front panel. Durable black finish matches factory styling for a clean, finished look. What it does:

• Covers and protects the appliance's lower front opening and underlying components
• Restores cosmetic appearance if the original is dented, cracked, scratched, or missing
• Helps keep pets and objects from contacting components behind the panel
• Provides the factory look and fit for a seamless exterior

• Disconnect power to the appliance before beginning any service
• Typically fastens with retaining tabs and/or screws; align tabs and snap or secure as needed
• Use basic hand tools and protect surrounding surfaces during removal/installation
• Inspect and replace clips for a secure fit

This trough drain channels defrost and condensation water from the evaporator area to the refrigerator drain pan, helping prevent pooling and ice buildup. Fits as the replacement evaporator-area drain trough in compatible refrigerators. What it does:

• Collects and directs defrost/condensation water away from the evaporator compartment
• Helps prevent water pooling inside the fresh food or freezer section
• Reduces ice formation around the evaporator area when functioning properly
• Works with the drain tube and pan to route water safely to the drain pan

• One trough drain

• Disconnect power to the appliance before starting any service
• Remove interior shelves, drawers, and the evaporator cover to access the trough
• Inspect surrounding seals and the drain tube for clogs; clear any debris before installing
• Reassemble panels and restore power; run a short defrost cycle or pour warm water to verify proper drainage

This evaporator coil cover protects the refrigerator's evaporator assembly and helps direct airflow for more consistent cooling. It replaces a damaged or missing interior cover to keep the coil shielded and the compartment operating as intended. What it does:

• Shields the evaporator coil from contact and debris to prevent accidental damage
• Helps direct cold air across the evaporator for more even cooling performance
• Reduces unwanted airflow patterns that can cause frost buildup or uneven temperatures
• Covers sharp edges on the evaporator assembly for safer access during service

• One evaporator coil cover

• Disconnect power to the appliance before beginning any repair
• Remove interior panels and shelves as needed to access the evaporator area
• Handle the evaporator and cover carefully to avoid bending fins or damaging nearby components
• Fully defrost the evaporator before installing the new cover

This condenser coil assembly helps release heat from the refrigerant so your refrigerator can keep food cold and run efficiently. Replaces a worn or damaged condenser to restore normal cooling performance. What it does:

• Releases heat from the sealed refrigerant loop so the compressor and evaporator can maintain proper temperatures.
• A failing condenser can cause the refrigerator to run continuously, run hot, or raise internal temps.
• Damaged or clogged condenser fins can increase energy use and make the compressor work harder.
• Restoring a functional condenser often reduces compressor strain and improves overall cooling consistency.

• One condenser coil assembly

• Disconnect power before servicing; follow all safety precautions.
• Access may require removing the rear or lower access panel; handle fins carefully to avoid damage.
• Avoid bending fins or contaminating the sealed refrigerant loop; do not attempt refrigerant repairs unless certified.

This tapping plate secures the mullion/vertical trim on a refrigerator, restoring a solid mount and proper door alignment. It replaces a damaged or missing mounting plate to reduce trim movement and help maintain a tight door seal. What it does:

• Provides a screw-ready mounting surface for the refrigerator mullion/trim
• Helps keep the mullion firmly in place to prevent wobble or rattling
• Restores proper mullion alignment that can affect door fit and sealing
• Addresses symptoms like loose or shifting mullion trim and uneven door gaps

• Disconnect power and empty doors as needed before working on the mullion area
• Align plate with the mullion mounting area and secure with appropriate screws
• Use hand tools and wear gloves to protect hands from sharp edges

The Ice Maker Cooling Duct is an OEM part for Frigidaire refrigerators. It directs cold air flow to the ice maker.

Causes of failure can be blockages or damage to the duct over time that impact efficient air flow.

Symptoms of a bad cooling duct include:

• Inconsistently shaped or formed ice cubes
• Slow or reduced ice production
• The ice maker failing to dispense ice properly
• Higher than normal interior refrigerator temperatures near the ice maker

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.