Whirlpool Freezer Parts

Seals the evaporator cover to prevent air leaks and frost buildup. Replace if you notice ice accumulation or warm air intrusion. Confirm fit by model.

This interior oven light bulb provides replacement illumination so you can check cooking progress without opening the door. Fits the oven light socket and restores visible, reliable interior lighting. What it does:

• Replaces a burned-out oven light so you can see inside the oven while cooking
• Restores safe, visible interior lighting for monitoring baking and broiling
• Stops flickering or intermittent light caused by a faulty bulb
• Works with compatible oven light housings and sockets

• One replacement interior oven light bulb

• Disconnect power to the appliance before replacing the bulb to avoid shock
• Allow the oven and bulb to cool completely before touching
• Remove the light cover, swap the bulb, and reinstall the cover
• Handle the bulb with a cloth or gloves and do not overtighten when installing

This refrigerator door gasket creates an airtight seal around the door to keep cold air in and warm air out, helping maintain proper temperature and energy efficiency. Replacing a worn gasket restores a reliable seal and prevents frost or moisture issues.

• Seals the perimeter of the refrigerator door for consistent cooling
• Helps reduce frost, condensation, and temperature swings
• Common symptoms include doors not sealing well, warm spots, or excess moisture

• Unplug the appliance before service
• Soften the gasket in warm water to improve flexibility and fit
• Clean and inspect the door channel; start seating the gasket at the corners
• After installation, close the door and check for uniform contact around the seal

Replacement pivot hinge for freezer or refrigerator doors. Restores smooth opening and proper alignment when the original hinge is cracked, worn, or broken.

Start relay for refrigerator compressors that helps the compressor begin running at power-up. Replacing a failed relay can restore normal starting behavior and resolve common startup symptoms. What it does

• Provides the initial start current path to the compressor during startup.
• Allows the compressor to reach running speed, then drops out once the motor is running.
• Common symptoms a bad relay may cause: compressor clicking, humming without starting, intermittent cooling or frequent cycling.
• Installed as the electrical component used only on compatible compressor assemblies.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Access the relay at the compressor; remove and replace the relay only after confirming diagnostics.
• Dispose of the old electrical part per local regulations.

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

Replace your refrigerator door gasket to restore an airtight seal, maintain consistent temperature, and improve energy efficiency. Confirm fit with your model.

0.6 oz. platinum touch-up paint with brush for appliances. Repairs scratches, chips, and gouges on doors, handles, and trim panels. Acrylic formula.

Motor mounting bracket for freezers. Secures the motor assembly in place. Replace if cracked, broken, or causing motor misalignment or vibration.

This lock assembly secures the appliance door/lid and enables normal cycle starts by engaging the latch. Replaces a worn or broken lock to restore proper door closure and allow the unit to begin and complete cycles reliably. What it does

• Physically latches the door/lid so the appliance can start and run
• Provides the mechanical engagement the control checks before permitting operation
• Common symptom: door won't stay closed or latch does not engage
• Common symptom: appliance won't start, won't advance or shows a door/lock fault

• Disconnect power (and water supply for washers) before beginning any service
• Handle small parts carefully and note their orientation for reassembly
• If wiring is present, disconnect and reconnect matching connectors only; do not force

Fix a refrigerator that won't cool or run with this compressor overload protector. Prevents compressor damage from electrical overheating. Easy install.

Replacement door handle for freezer units. Installs on the exterior door to provide grip for opening and closing. Needed when original is cracked or broken.

Compressor won't start or cycles on and off? This overload protector prevents motor damage by cutting power during overheating. DIY-friendly fix.

Thin shim that aligns and levels your freezer door at the hinge point. Replace when worn, damaged, or missing to eliminate rubbing and uneven gaps.

Interior support plate for freezers and refrigerators. Mounts inside the cabinet to hold shelving or components. Replace if cracked, broken, or missing.