Whirlpool Range Gasket & Seal

This seal restores a tight barrier between two mating parts in your appliance to prevent leaks and contamination. Replacing a worn or cracked seal helps stop drips, drafts, and noise so the unit can run reliably.

• Forms a tight seal between components to contain fluids or air
• Helps prevent leaks, drips, condensation, or unwanted airflow at joints
• Maintains efficient performance and reduces noise or vibration from loose fits
• Common failure signs: visible cracks/flattening, moisture where parts meet, odors, or louder operation

• Disconnect power and shut off water before servicing
• Note the seal's orientation; remove the old seal and clean all mating surfaces
• Install without stretching; lightly moisten if specified by your service manual (avoid petroleum products unless directed)
• Reassemble and test for proper operation and any leaks

This oven door gasket creates a tight, heat-resistant seal between the door and the oven frame. It keeps hot air inside, helps the oven reach and hold temperature, and protects nearby surfaces from escaping heat. What it does

• Seals the gap around the oven door to reduce heat loss
• Supports accurate temperatures and more even baking performance
• Replaces gaskets that are brittle, flattened, torn, or frayed
• Common symptoms: heat felt escaping around the door, longer preheat/cook times, temperature swings, visible damage to the gasket

• One door gasket

• Disconnect power at the breaker and allow the oven to cool completely
• Open the door and pull the old gasket straight out of its retaining holes/clips
• Start at the top center; press the new gasket's tabs into place without stretching, ensuring corners are fully seated
• Close the door to confirm uniform contact all the way around the seal

This oven door gasket restores a tight seal between the door and the oven front frame. A proper seal reduces heat loss, supports accurate temperatures, and helps food bake and roast more evenly.

• Creates a heat-resistant seal at the door-to-cavity opening to contain heat and airflow
• Helps maintain stable oven temperatures and normal preheat times
• Replace if the seal is torn, frayed, brittle, flattened, burned, or leaking
• Helps resolve heat escaping around the door, uneven baking, or longer cook times

• Disconnect power; for gas appliances, also shut off gas. Allow the oven to cool completely
• Remove the old gasket by releasing end retainers or pulling it from the channel; clean the groove
• Install the new gasket without stretching; seat it evenly around the perimeter with corners aligned
• Close the door and check for uniform contact all around; adjust as needed per your model instructions

This oven door gasket fits select 30-inch models and restores a tight, heat-resistant seal between the door and oven cavity. Replacing a worn gasket helps contain heat, support accurate temperatures, and protect surrounding surfaces from excess heat.

• Maintains a thermal barrier to keep hot air inside the oven cavity
• Helps the oven reach and hold the set temperature
• Reduces heat escaping around the door for more consistent baking
• Replaces gaskets that are cracked, frayed, flattened, or leaking; common symptoms include long preheat times, temperature swings, or feeling heat escaping at the door edge

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the old gasket from the frame, noting the orientation of any end clips or pins
• Clean the frame/channel to remove debris for a proper seal
• Install the new gasket without stretching; seat clips/pins fully and check for even contact all around

This oven door gasket restores a tight seal between the door and oven cavity so your appliance can hold set temperatures. Replacing a worn seal helps reduce heat loss for more consistent preheating and baking results.

• Seals the gap between the oven door and frame to keep heat and moisture inside
• Helps maintain accurate oven temperatures and reduce energy loss
• Replace if the gasket is torn, hardened, flattened, frayed, or falling out of its channel
• Common symptoms: heat escaping around the door, long preheat, uneven baking, odors or smoke leaking from the oven

• Disconnect power and allow the oven to cool completely before servicing
• Gently pull the old gasket from the channel or unhook its retainers; note clip locations/orientation
• Press the new gasket evenly into the groove without stretching; align any corner pins/clips to match the original
• Close the door and check for uniform contact around the seal

Oven door gasket forms the heat seal around the oven door opening to keep heat inside for even cooking and efficient operation. Replaces worn or torn seals to reduce heat loss and improve bake performance. What it does:

• Seals the oven cavity to maintain proper cooking temperature and improve efficiency.
• Helps prevent heat and smoke from escaping around the door.
• Commonly used to address long bake times, uneven cooking, or visible gaps/damage at the door edge.
• Flexible design fits into the door channel to restore a snug seal.

• Disconnect power (and gas supply, for gas ovens) and allow the appliance to fully cool before starting.
• Inspect the door channel and remove old gasket; some models require partial door removal.
• Press the new gasket into the channel evenly; ensure any retaining clips or tabs are fully seated.
• Wear gloves to protect hands from sharp edges and avoid using sharp tools that could damage the new gasket.

Replacement gasket that restores a tight seal to the appliance door and helps prevent water or air leaks. Replaces worn, cracked, or compressed seals so the door closes properly and reduces moisture or heat loss. What it does:

• Seals the door opening to stop leaks of water, steam, or heated air.
• Helps maintain proper temperature and efficiency by preventing air exchange.
• Reduces condensation, odors, and cycling caused by a poor seal.
• Common signs you need this part: visible gaps or damage, leaks around the door, excess moisture, or poor heating/cooling performance.

• Disconnect power and water (if applicable) and allow the appliance to cool before starting.
• Clean and dry the mating surface to ensure a proper fit; remove old adhesive or debris.
• Align the gasket into the door channel or groove and press evenly; avoid stretching the material.
• If the door or mounting hardware is bent or damaged, repair those parts before installing the gasket.

This door gasket seals the broiler/bottom-oven door to help retain heat for more even broiling and reduce stray heat into the kitchen. It replaces worn or damaged seals that allow heat loss or uneven cooking. What it does:

• Creates a heat-tight seal around the broiler/bottom-oven door to improve cooking performance
• Helps prevent heat loss, uneven broiling, or extended cook times caused by gaps in the door seal
• Wear signs include visible cracks, flattened or torn material, and gaps around the door edge
• Replacing a damaged gasket can reduce smoke from burning food debris caught in a torn seal

• Disconnect power (and gas, if applicable) and allow the appliance to cool fully before starting
• Remove the broiler drawer or door per the owner's manual to access the gasket channel
• Clean the gasket channel of debris before seating the new gasket; press the gasket into the retainer evenly

This door gasket seals the refrigerator/freezer door to keep cold air in and maintain consistent temperatures. A correct replacement restores the door seal to help prevent leaks, frost buildup, and inefficient cooling. What it does:

• Replaces a damaged or worn door seal to restore a tight closure between door and cabinet.
• Helps stop cold air from escaping, reducing frost buildup and uneven temperatures.
• Minimizes energy loss caused by gaps or cracks in the existing gasket.
• Addresses symptoms such as visible cracks, gaps when door is closed, or increased running time.

• One white door gasket (as pictured).

• Unplug the appliance or shut off power before starting any repair.
• Inspect and clean the gasket channel and mating surfaces before installing the new seal.
• Start by seating the gasket into the corners, then press the gasket evenly into the channel around the door.
• Avoid using sharp tools that could tear the gasket; refer to the appliance manual for any model-specific steps.

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

This switch bracket mounting seal replaces a worn or damaged seal that cushions and protects the door or control switch mounting area. It helps keep the switch assembly seated and reduces debris and moisture intrusion for reliable operation. What it does:

• Seals the switch bracket mounting area to protect the switch from lint, dust and moisture
• Helps keep the switch properly positioned for accurate door or control sensing
• Can prevent intermittent or failed switch contacts caused by contamination or misalignment
• Useful when replacing a brittle, torn or missing mounting seal during switch or door repairs

• Disconnect power to the appliance before starting any repair
• Remove the door or panel per service instructions to access the switch bracket area
• Fit the seal into the bracket groove or around the switch housing, ensuring full seating without stretching
• Inspect adjacent clips or screws and reuse or replace as needed; test the switch function after reassembly

This replacement knob grommet cushions and centers a control knob on the console, helping reduce wobble and protect the panel from wear for smoother, more secure knob operation. What it does

• Centers and cushions the control knob for proper alignment and tactile feel.
• Helps reduce knob wobble, rubbing, and wear on the control panel.
• Can address symptoms like loose, uneven-feeling, or noisy knobs when turning.
• Fits the knob mounting on compatible Whirlpool control panels for a restored fit.

• Disconnect power to the appliance before servicing.
• Remove the control knob, press the grommet into the panel opening, then reinstall the knob; generally requires no special tools.
• Inspect the knob and shaft—replace if damaged, as a damaged shaft can prevent a secure fit.
• Reconnect power and confirm proper knob alignment and operation after installation.

Seals the appliance door to prevent leaks and keep the interior working as intended. Replace a cracked, torn, or hardened gasket to stop leaks, reduce odor and mold, and restore a reliable door seal. What it does:

• Forms a tight seal between the door and cabinet to prevent water, air, or heat loss
• Stops common symptoms like visible cracks or gaps, water pooling, and persistent odors
• Restores proper containment for cleaning, heating, or washing cycles
• Matches the OEM channel/retainer design for a secure fit

• Disconnect power and water before beginning any repair
• Remove the old gasket, thoroughly clean the mounting area, then seat the new gasket into the door channel or retainer
• Work the gasket evenly around the door; avoid overstretching and ensure all beads/clips are fully engaged

This door gasket seals the oven door to help keep heat and cooking moisture inside for more even baking and efficient operation. It replaces a damaged or worn seal to restore a snug, continuous closure. What it does

• Provides a heat-resistant seal around the oven door to reduce heat loss
• Helps prevent hot air and steam from leaking during cooking
• Can reduce uneven baking or longer cook times caused by gaps
• Visible signs of failure include cracks, flattening, or gaps around the door edge

• Disconnect power to the appliance and allow the oven to cool completely before starting.
• Remove the old gasket by pulling from the retention channel; press the new gasket into the same channel until fully seated.
• Check the seal all the way around the door and make minor adjustments for an even fit.