Whirlpool Range Hinge Parts

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

Oven door would no longer close completely, ordered replacement hinges, 30 minute repair. Read more

I ordered both hinges (if the nylon roller was bad on the left, it was probably going to go bad on the right side as well). The web site was easy to navigate, order process simple. Hinges arrived quickly. Slide the oven door up and off. unscrew the three screws for the hinge. You need to then pull up with some force (there is a big spring in there), and twist the hinge to get the last bit out. I used a hemostat to hold the spring and keep it from falling back into the hole. removed the... Read more

• Door won't close

I ordered both hinges (if the nylon roller was bad on the left, it was probably going to go bad on the right side as well). The web site was easy to navigate, order process simple. Hinges arrived quickly. Slide the oven door up and off. unscrew the three screws for the hinge. You need to then pull up with some force (there is a big spring in there), and twist the hinge to get the last bit out. I used a hemostat to hold the spring and keep it from falling back into the hole. removed the... Read more

Watched video from AppliancePartsPros.com, ordered part. I followed instructions on video and oven door works great now!!! Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

• Door won't close

Replaced the hinge and receiver. Read more

• Door won't close

For the third time in four years, the hinges failed on my KitchenAid wall oven. The appliance is out of warranty and KitchenAid does not consider this to be worthy of any recall. I was tired of paying the appliance repairman to change out the hinges, so I ordered the part online. Appliance Parts Pros is an awesome site for identifying the part you need, and they deliver quickly. Note that you probably need TWO hinges--they do not come as a set--and KitchenAid likes to make their model numbers... Read more

Replace two door hinges works great now. Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

Replaced both hinges. Easiest repair I’ve done on this unit. Took less than 20 minutes from start to finish. Read more

Removed oven door. Removed front panel from oven door. Replaced both door hinges. Read more

• Door won't open or close

The replacement hinge unit arrived in just two days. The JennAire (Maytag) oven door is fairly typical in that it easily lifts off of the hinge bars. Once the door is off then removing two screws is all that's required to remove the hinge unit from the oven. The new hinge slides up into place and while you hold it up inside of its location putting the old screws back in is very easy. After sliding the door back down onto the hinge bars the oven is as good as new Read more

• Door won't close

Replaced the hinges after watching YouTube video. Read more

I had to take out the bottom drawer that holds pans. Disconnect the power and pull the oven out. Removed door, rear panel that held the screws for the side panel and lift up and out the side panel. After that it was straight forward as to replacing the hinge. Spent more time cleaning the florr where the oven was than installing the hinge. Read more

• Door won't close

This oven was a Kenmore model #66595822003. I replaced both spring hinges. This oven was a white oven so it took the MFG# WP8053807 hinge (order two of them). They are the same hinge. No left or right. To get the door off the oven, open the door all the way open, I installed pins (preferably only 1/4" long) in the holes of both hinges. Then remove the spring steel retainers above old hinges in the oven frame. These holds hinges in place. Now close the door until hinge stops on pins. Lift up... Read more