Whirlpool Range Fuse Or Sensor

This thermal fuse is a heat-sensitive safety cutoff that protects dryers from overheating by opening the electrical circuit at high temperature. It replaces a failed fuse to restore safe thermal protection and normal dryer operation. What it does:

• Opens the circuit when internal dryer temperatures exceed safe levels to prevent fires
• Prevents the heating element or burner from receiving power during an overheat condition
• Commonly linked to symptoms like no heat, intermittent heating, or a dryer that runs but won't complete cycles
• Works as a single-use safety device—once blown it must be replaced

• One thermal fuse (rated 152°C)

• Disconnect power to the appliance before accessing or replacing the fuse
• Locate the fuse on the dryer's blower housing/heater assembly per your model's service info
• Replace only with the correct rated fuse; do not bypass or jumper the device
• If the new fuse blows again, inspect the heating system, thermostat, venting, and airflow for faults

This protective fuse safeguards the appliance's electrical circuit. When an overcurrent or short occurs, it opens the circuit to cut power and help prevent damage. Replacing a blown fuse can restore power once the underlying issue is corrected.

• Opens the circuit when current exceeds its design limit or a short is detected
• Helps protect control and other internal components from electrical damage
• Typical symptoms of a failed fuse include no power, dead display/controls, won't start, or immediate power loss
• An underlying electrical fault is likely present and should be diagnosed

• Disconnect power at the breaker or unplug the appliance before servicing
• Replace only with the exact type and rating specified for your model; never bypass or upsize a fuse
• Inspect wiring and components for the root cause of the blown fuse before restoring power
• If servicing a microwave, follow the service manual and discharge the high-voltage capacitor; consider service due to shock risk

The Microwave Thermostat is a reliable component designed to regulate temperature in your microwave, ensuring optimal performance and safety. This genuine OEM part is specifically compatible with a wide range of Samsung microwave models, providing a secure and precise fit. By maintaining the correct temperature levels, the Microwave Thermostat helps prevent overheating and extends the lifespan of your appliance. Installing the THERM thermostat restores your microwaveGÇÖs functionality, allowing you to enjoy consistent heating results every time. Crafted from high-quality materials, this thermostat offers durability and dependable operation, giving you peace of mind with your repair. Whether your original thermostat is malfunctioning or needs replacement, the Microwave Thermostat is the perfect solution to maintain your microwaveGÇÖs efficiency and reliability. Trust in this genuine OEM part to keep your Samsung microwave running smoothly and effectively.

This lower thermostat monitors and helps regulate temperature in the appliance's lower compartment by opening and closing an electrical contact. Replacing a failing thermostat can restore normal cycling and help the compartment maintain correct temperatures. What it does:

• Senses lower-compartment temperature and completes or breaks the circuit to control cooling cycles.
• Helps the compressor/fan cycle on and off to maintain set temperatures.
• A defective thermostat may cause warm temperatures, continuous compressor operation, or inconsistent cooling.
• Matches the OEM function and mounting location for lower compartment temperature control.

• Disconnect power to the appliance before beginning any service.
• Label or tag wires before removal and reconnect exactly to the same terminals.
• Handle the sensor and capillary carefully; avoid kinking or excessive bending. After installation, restore power and verify normal cycling.

This fixed high-limit thermostat is a safety device for your oven. It monitors temperature and opens the circuit if the cavity overheats, helping protect components and restore normal heating when the failed thermostat is replaced.

• Provides over-temperature protection for the oven's heating circuit
• Opens the electrical circuit at a preset limit to stop heat when overheating occurs
• Typical symptoms of failure: oven won't heat, shuts off during use, or won't start after a self-clean cycle
• Often tests open for continuity at room temperature when failed

• Disconnect power at the breaker before servicing; oven circuits carry dangerous voltage
• Allow the appliance to cool completely before access
• Access location varies by model; the thermostat is typically mounted on or near the oven cavity or rear panel
• Move wires one at a time to the new thermostat, ensure tight spade connections, remount securely, restore power, and test

This fixed thermostat monitors and limits temperature to protect the appliance's system and components. It's a simple, non-adjustable sensor/limit switch used where a set cutoff temperature is required for safe operation. What it does:

• Opens or cuts power when the monitored temperature reaches its fixed limit to prevent overheating
• Helps stop continuous heating cycles caused by a failed control or sensor
• Commonly used as a safety cutoff in temperature-control circuits
• Can resolve symptoms like persistent overheating, failure to stop heating, or temperature-related shutdowns

• One fixed thermostat (single unit)

• Disconnect power before inspecting or replacing the thermostat to avoid shock or damage
• Handle gently; avoid bending terminals or stressing sensing elements

This high-limit thermostat is a temperature safety switch that helps prevent overheating by opening the circuit when temperatures exceed safe limits. It restores normal operation once the temperature cools, protecting the appliance and reducing fire risk. What it does:

• Monitors internal temperature and opens the circuit if heat gets too high
• Prevents overheating that can cause damage or burn odors
• Commonly replaces a failed or intermittently tripping thermal safety switch
• Works as part of the appliance's temperature-safety system, not a primary temperature control

• Disconnect power to the appliance before attempting replacement
• Observe proper wiring orientation and secure terminal connections
• Replace only with the exact part specified for your appliance

This thermostat temperature limiter helps stop heating when temperatures exceed safe levels, protecting the appliance and preventing overheating. It fits specific Whirlpool systems and restores proper temperature control when the limiter has failed. What it does

• Acts as a safety cutoff to interrupt heating when internal temperatures get too high.
• Prevents the appliance from continuing to heat during an over-temperature condition.
• Common symptom: appliance runs but produces little or no heat.
• Common symptom: heating cycles off prematurely or intermittently.

• One thermostat temperature limiter.

• Disconnect power (unplug or shut off breaker) before accessing the appliance.
• Handle and route wiring carefully; replace only with the exact OEM part number.
• Test circuits with a multimeter to confirm thermostat failure before replacing.

This temperature limiter switch stops heat buildup by opening the circuit when temperature exceeds safe limits. It restores proper thermal protection for the appliance's heating system and helps prevent overheating-related damage. What it does:

• Opens the heating circuit if internal temperature rises above the thermostat's limit to prevent overheating.
• Commonly used as a safety cutoff for dryers, ovens or other appliance heating systems.
• Symptoms of a failing limiter: no heat, intermittent heating, or an appliance that won't start its heating cycle.
• Works with the appliance's control and heating elements to maintain safe operating temperatures.

• Disconnect power before inspecting or replacing this part to avoid shock or injury.
• Replace with the exact part number to maintain proper temperature protection.
• If the limiter has tripped, inspect heating element, venting and related components for root causes before reassembly.