Whirlpool Refrigerator Auger, Helix, Crusher

Ice dispenser not working or auger keeps falling off? This coupling connects the motor to the auger. Simple 15-minute DIY fix restores ice dispensing.

Ice bin cracked or warped? This container stores ice from your icemaker and guides cubes to the dispenser. Simple plug-and-play replacement part.

This ice deflector guides ice cubes from the icemaker into the ice bin to help keep ice delivery consistent and reduce cube jams or spills. It's a simple replacement that restores proper ice routing in compatible refrigerators. What it does:

• Directs ice cubes from the icemaker into the ice bin for orderly dispensing
• Helps prevent ice clumping and blockages that can stop ice flow
• Keeps ice moving away from the icemaker assembly and into the bin
• Restores proper alignment and function after a cracked or missing deflector

• Disconnect power to the refrigerator before servicing to avoid electrical or mechanical injury
• Remove the ice bin or access panel per your model's service instructions to reach the deflector
• Part typically snaps or slides into place; reuse existing fasteners unless new hardware is supplied
• After installation, reconnect power and run the icemaker through a cycle; discard any ice made during the repair if contamination is suspected

This complete unit produces ice cubes automatically within the freezer compartment of your refrigerator. Replace if ice production stops completely, produces hollow or malformed cubes, or leaks water inside the freezer.

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

Ice maker not producing cubes or stopped working? This complete ice maker assembly restores automatic freezing, harvesting, and shutoff. Typical DIY repair.

This complete ice maker assembly produces and dispenses ice cubes in your refrigerator's freezer compartment. It includes all the internal mechanisms needed for ice production including the water inlet, freezing chamber, and ejection system. Replace this assembly if your refrigerator stops making ice, produces malformed ice cubes, or if ice production is significantly slower than normal.

Ice container cracked or broken? This refrigerator ice cube bin stores ice from your automatic ice maker. Simple snap-in installation takes minutes.

Cracked or broken ice cube tray? This plastic tray restores manual ice-making in your refrigerator. Simple drop-in replacement, no tools required.

Fix ice maker not making ice or leaking with this complete assembly. Most DIYers complete installation in under an hour with basic tools and screwdriver.

Note: Per the manufactuer, this is an icemaker only. For the harness use part number W10508673 and for the shut-off arm use part number W11342242.

Ice maker dripping or splashing water? A cracked or clogged fill cup spout disrupts water flow. This direct-fit part restores clean dispensing in under an hour.

Ice not dispensing or auger broken? This refrigerator ice crusher auger transfers ice from bucket to dispenser. Moderate DIY repair in 30 minutes.

Ice dispenser not crushing properly? This blade mounting block secures crusher blades in the ice container head, eliminating noise and uneven crushing.

The Icemaker Assembly is an OEM part for Whirlpool refrigerators. It includes all the necessary components to replace or install an icemaker in your refrigerator, ensuring you can consistently produce and store ice efficiently

Symptoms of a failing Icemaker Assembly include:

• No ice production or very little ice being made
• Ice cubes that are smaller than normal or misshapen
• Leaking water in the freezer compartment
• Unusual noises during the ice making cycle, such as clicking or buzzing

Causes of a bad icemaker can include issues with the water inlet valve, freezer temperature not being cold enough, or mechanical failures within the icemaker itself, such as a faulty motor or an obstructed fill tube.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Ice not dispensing or leaking from bottom? This ice bucket and auger assembly stores ice and moves it to the dispenser. Moderate DIY repair with video.