Parts for Crosley CDE6505W: 01 - Base, Heater & Motor Parts

Appliance won't start or trips breaker? This ground screw secures the grounding conductor to the chassis for safe electrical connection. Simple fix.

Dryer running too hot or overheating? The hi-limit thermostat cuts power to the heating element when temps exceed safe limits. Easy DIY replacement.

10 - 16 x 1/2

Dryer not heating or blowing cold air? The heating element converts electrical energy to heat for drying. Most DIYers complete this repair in 45-60 minutes.

Dryer won't start or heat? The thermal fuse trips when overheating occurs, often from clogged vents. Easy DIY fix with our video guide.

Fix a dryer that hums but won't turn with a new drive motor. This repair addresses seized bearings and worn motor assemblies. Moderate DIY project.

Maintains tension on the drive belt to keep it tight around the drum and motor pulley. Replace if the pulley is worn, cracked, or causing squealing noises.

Fix no airflow or squealing dryer with this blower wheel replacement. Restores proper air circulation through drum and exhaust. Moderate DIY repair.

Fix loose or rattling parts with this 1/4-20 nut. Secures components in dryers, washers, and microwaves. Quick 5-minute repair restores stability.

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

10 - 16 x 1/2

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This cycling thermostat regulates exhaust temperature by switching the heater on and off to maintain proper drying heat. Replacing a failed thermostat restores consistent temperatures, helps auto-dry timing, and protects against fabric-damaging overheating.

• Controls the heating circuit to maintain target drying temperatures
• Provides temperature feedback for accurate auto-dry operation
• Common symptoms: long dry times, very hot drum/cabinet or scorching odors, auto-dry not advancing correctly, or no heat if the thermostat fails open
• Typically mounted on the blower housing to sense exhaust air temperature

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the thermostat (commonly on the blower housing); remove the necessary panel(s)
• Transfer wires one at a time to the new thermostat and mount it flat against the housing
• Reassemble, verify clear venting/airflow, and run a test cycle