Parts for Admiral GS2125CEEW: 02 - Controls Parts

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This mechanical rotary defrost timer controls and advances the refrigerator's defrost cycle so the evaporator periodically melts frost buildup, helping restore normal cooling. It replaces a worn or stuck timer to return automatic defrost operation. What it does

• Advances the fridge's defrost cycle on a set schedule so the evaporator heats and melts frost
• Stops the compressor during defrost so frost is removed without cooling loss
• Common symptom: excessive frost buildup on evaporator or freezer compartment
• Common symptom: refrigerator or freezer runs constantly or does not cool properly

• One defrost timer (rotary)

• Disconnect power to the appliance before starting any repair
• Locate timer (control panel, kick plate, or rear panel depending on model) and note original orientation before removal
• Remove mounting screws and electrical connector(s); install new timer in the same position and reconnect wiring

A replacement door gasket that restores a tight seal around the oven door to help maintain proper cooking temperature and improve efficiency. Fits Whirlpool ovens and ranges that use part A3189394. What it does

• Seals the oven cavity to reduce heat loss and help maintain consistent cooking temperatures.
• Helps prevent heat from escaping around the door, improving energy use and cook results.
• Worn, torn, or flattened gaskets can cause uneven baking or longer cook times.
• Replacing a damaged gasket can reduce hot spots on the exterior and nearby cabinetry.

• Disconnect power and ensure the oven is completely cool before starting.
• Remove the old gasket by pulling it out of the door channel; clean the channel before installing the new gasket.
• Press the new gasket into the channel around the full perimeter, working from one corner and ensuring an even fit.

Size: 8 x 1-1/4 inch.

This control wire harness connects the appliance control board to sensors, switches and powered components to restore electrical communication and proper function. It replaces a damaged or loose harness to help resolve intermittent or non-responsive controls. What it does:

• Carries power and low-voltage control signals between the main control board and components.
• Restores operation when frayed, burned, or cracked wiring causes intermittent circuits or loss of specific functions.
• Helps stop faults caused by broken connector tabs, corroded terminals, or detached plugs.
• Resolves error codes or unresponsive buttons that trace back to wiring faults.

• Disconnect power (unplug or switch off breaker) before starting; shock hazard exists.
• Compare the new harness to the original for connector type and routing before installing.
• Route and secure the harness exactly as the original using existing clips/retainers to avoid pinching or heat exposure.