Parts for Maytag MEW6630DDS19: 02 - Upper Oven Door Parts

The Oven Door Hinge is an OEM part for Whirlpool wall ovens and ranges. Located on both sides of the oven door frame, these metal hinges provide the pivoting connection that allows smooth opening and closing of the door during cooking cycles.

Causes of failure can include wear of the hinge joints from repeatedly bearing the weight of the heavy oven door over thousands of uses. Exposure to high heat during cooking may gradually deteriorate lubricating grease or materials.

Symptoms of faulty hinges include:

• Door rubbing or sticking during opening/closing
• Off-center alignment when shut or inability to fully latch
• Noisy squeaking or grinding emerging from hinges
• Hinges loosened from screws/fastenings or mechanisms seized

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This high-temperature gasket seals the oven door to the cabinet. Replacing a worn seal helps your oven preheat more efficiently, hold steady temperatures, and reduces heat and vapor escaping around the door edge.

• Maintains a tight seal between the door and oven cavity to retain heat
• Supports accurate, consistent baking and roasting temperatures
• Helps reduce longer preheat or cook times caused by heat loss
• Replaces seals that are torn, brittle, flattened, or frayed

• Disconnect power and allow the oven to cool completely before servicing
• Open the door and remove the old gasket, noting clip/screw locations and orientation
• Clean the mounting channel; press the new gasket in place without stretching it
• After installing, preheat and check for even contact all around the door

Color: Black

Replace a damaged or discolored oven handle with this white door handle. It restores a secure, comfortable grip and a clean look so you can open and close your range or wall oven door with confidence.

• Provides the handhold used to open and close the oven door
• Replaces cracked, broken, loose, or missing handles
• Helps restore safe handling and original appearance
• White finish to match compatible models

• Disconnect power at the breaker and allow the oven to cool completely
• Support the door/outer glass; remove inner door screws to access the handle mounts
• Transfer any end caps or hardware from the old handle, if applicable
• Tighten fasteners evenly; reassemble and check door operation

Color: Black. For white order WP74011768. For bisque order WP74011778. For screws order WP74006515.

This door insulation replaces the soft thermal fill inside a laundry or appliance door to help reduce heat transfer and noise. Restores proper thermal buffering to improve performance and helps maintain stable internal temperatures. What it does:

• Replaces worn or damaged insulation pack inside the door cavity
• Helps limit heat loss and reduces noise from the appliance during operation
• Helps protect internal components from temperature fluctuations
• Useful when insulation is compressed, torn, or missing after door service

• One door insulation piece

• Designed to sit inside the door cavity; access requires removing the door or inner door panel
• Inspect surrounding seals and fasteners and replace any damaged hardware
• Wear work gloves to avoid contact with fibrous insulation material; avoid inhaling dust

This door insulation replaces the foam panel inside a refrigerator or freezer door to help maintain proper internal temperatures and improve energy efficiency. It restores the thermal barrier behind the inner door panel for more consistent cooling. What it does:

• Replaces the foam thermal barrier inside the door to help keep cold air in and warm air out
• Helps reduce frost buildup and uneven cooling caused by damaged or missing insulation
• Supports gasket sealing by filling the cavity behind the inner door liner
• Can reduce run-time caused by air leakage around a compromised door

• One door insulation panel

• Disconnect power before starting and work with the appliance empty and doors open
• Remove the inner door liner or access panel to access the insulation cavity
• Handle edges and metal parts carefully; wear gloves and eye protection
• Only use OEM-specified fasteners and replace any damaged clips or sealing foam as needed

This replacement door insulation pad helps restore the oven door's thermal barrier so the appliance holds heat more efficiently and runs quieter. Designed as the internal padding used behind the door liner. What it does:

• Replaces worn or damaged inner door insulation to help maintain cooking temperature and reduce heat loss
• Reduces outside-door heat and can help limit condensation on the outer door surface
• Helps dampen noise caused by oven operation and rattling door panels
• Use when insulation is torn, compressed, burned, or missing

• One inner door insulation pad

• High-level tear-down of the oven door is typically required; follow the manufacturer's service manual for safe disassembly
• Disconnect power (and gas if applicable) and allow the appliance to cool completely before starting work
• Handle insulation with care and use gloves and a dust mask if the material is friable
• Reassemble panels and fasteners to factory torque and verify the door seals correctly after installation

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Screw is an OEM part for Whirlpool appliances. This specific screw is used in various locations within Whirlpool appliances, securing components and ensuring the stability and proper alignment of parts. It is designed to fit precisely and maintain a firm hold, contributing to the overall functionality and safety of the appliance.

Over time, screws can become worn or stripped due to regular use, corrosion, or over-tightening. 

Causes of a bad screw include wear and tear, exposure to moisture leading to rust, and over-tightening which can strip the threads.

Symptoms of a bad screw include:

• Loose or wobbly components
• Misalignment of parts
• Noise due to vibrating or loose parts
• Difficulty in securing or removing the screw

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.