Randy S Houston , TX June 24, 2017 Appliance: Maytag 30" Built-In Microwave/Electric Oven Combo Self-Clean JMW9330DAB16 The control panel was no longer working lights were not coming on no beeps could be heard hen you hit a key on the control panel it first started with the 3 6 and 9 keys and became worse I replaced the old control panel with a new one. I also changed out the door seal to help prevent the control panel from going bad a second time. It was the heat from the oven getting to the keypad on the control panel that caused it to go bad. Read More... 4 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Screwdrivers, Socket Set
Jeffrey W Hudson , WI December 14, 2019 Appliance: Maytag 30" Built-In Electric Oven Self-Clean Convection JJW9330DDS13 Buttons on stove quit working. We have this model in stainless steel but couldn't find a stainless control panel anywhere so we just settled for the black one to hopefully get a few more years of life. The job was easy and straight forward. All that you need is a phillips and hex-nut screwdriver. Once you get the oven slid out a bit there are just four hex nuts that hold the panel to the frame. Pop those out and the panel comes off after which you disconnect the two ribbons and unscrew the board from the panel. Replace the old with the new, reassemble and wah-la I had a working stove again. I also chose to replace the 10 year old door seal as it was a little crusty and leaking heat. That couldn't have been easier either as the tabs on the seal line up with the holes in the door. Easy press fit. Probably 20 minutes from start to finish. Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers
Susan B Miami , FL August 19, 2016 Appliance: Maytag 30" Built-In Electric Oven Self-Clean Convection JJW9330DDB13 Door gasket was dry hard and dirty The gasket or door seal arrived, pulled the old one out, attached the new one and it was extremely easy. Make sure to line up the clips with the holes before you start. I started at the bottom right and worked my way around to the bottom. Then push each end into the two larger holes in the bottom of the door with a small screwdriver and that is it. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Donald P Edmond , OK May 22, 2015 Appliance: Jenn-Air Electric Wall Oven WW30430PC It needed a new seal and new hinges The seal was super easy, no need to disassemble the door. Just push the small pins in and when you get to the ends where you tuck into the door, just take a chopstick or small wooden spoon handle and push in to the two holes, very simple. The hinges required the door to be removed completely. This is easily done but they can be heavy, our are pretty hefty. Open the door, remove the brackets that cover the top of the hinge, raise the door to the semi open position and lift straight up. From there, disassemble the door, replace hinges (you do not need directions as everything is self explanatory. Replace hinges and put the door back in the same way you removed it. Remember, the new hinges have little safety pins so you need to pull those out or the door wont shut completely. But do not remove them until you have the door back in the oven! Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Pliers, Screwdrivers
Jonathan C Los Alamos , NM November 15, 2020 Worn out oven door seal Replaced seal. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Pliers