Parts for Amana DRB1801AC / PDRB1801AC1: 04 - Door Assemblies Parts

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This screw secures appliance panels and components to keep assemblies stable and aligned during normal use. It's a direct-fit fastener used where the factory requires a specific screw shape and thread. What it does:

• Fastens trim, panels, brackets, or internal components to the cabinet or frame
• Restores secure mounting when original fasteners are missing or stripped
• Helps eliminate rattling, vibration, or loose parts caused by a missing screw
• Matches OEM fit and fastening points for correct assembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace only the damaged or missing screw; confirm orientation and thread engagement before final tightening
• Disconnect power and follow all safety precautions before servicing appliances

This screw secures appliance panels and components to keep assemblies stable and aligned during normal use. It's a direct-fit fastener used where the factory requires a specific screw shape and thread. What it does:

• Fastens trim, panels, brackets, or internal components to the cabinet or frame
• Restores secure mounting when original fasteners are missing or stripped
• Helps eliminate rattling, vibration, or loose parts caused by a missing screw
• Matches OEM fit and fastening points for correct assembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace only the damaged or missing screw; confirm orientation and thread engagement before final tightening
• Disconnect power and follow all safety precautions before servicing appliances

Size: 63-1/2 x 35-1/2 x 2-5/8 inch.

This door stop replaces the small bumper that cushions and limits the door's travel so the door closes smoothly and avoids hard impacts. It restores normal door movement and reduces noise from slamming or catching. What it does

• Acts as a bumper/stop to limit how far the door opens or closes
• Cushions the door to prevent hard impacts and reduce noise
• Helps keep the door aligned and prevents catching or uneven closing
• Commonly replaced when the stop is worn, cracked, missing, or deformed

• One door stop

• Disconnect power (unplug or switch off breaker) before starting any repair
• Removal/installation typically requires basic hand tools and access to the door hinge/stop area
• Align the new stop in the same position as the old one and secure per the appliance's hinge/trim layout
• Reuse the original fasteners unless replacements are specified

This door stop replaces the small bumper that cushions and limits the door's travel so the door closes smoothly and avoids hard impacts. It restores normal door movement and reduces noise from slamming or catching. What it does

• Acts as a bumper/stop to limit how far the door opens or closes
• Cushions the door to prevent hard impacts and reduce noise
• Helps keep the door aligned and prevents catching or uneven closing
• Commonly replaced when the stop is worn, cracked, missing, or deformed

• One door stop

• Disconnect power (unplug or switch off breaker) before starting any repair
• Removal/installation typically requires basic hand tools and access to the door hinge/stop area
• Align the new stop in the same position as the old one and secure per the appliance's hinge/trim layout
• Reuse the original fasteners unless replacements are specified

This freezer door gasket forms the airtight seal between the door and cabinet. Replacing a worn gasket restores a proper seal, helping maintain temperature and reducing frost and moisture for more reliable freezer performance.

• Creates the perimeter seal to keep cold air in and humid air out
• Helps prevent frost/ice buildup and temperature swings inside the freezer
• Supports smooth door closing and even contact around the frame
• Common symptoms: tears, cracks, warping, gaps, persistent frost, or warm spots

• Unplug the appliance before servicing
• Warm/relax the new gasket in hot water or with a hair dryer on low to improve fit
• Start at a corner and press the gasket lip fully into the retainer channel; ensure corners seat first
• Check the seal with a paper test and gently reshape as needed; allow time for the gasket to conform

This part has been discontinued and is no longer available.

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This refrigerator door gasket restores a tight seal between the fresh food door and cabinet to help maintain proper temperatures and reduce moisture. Replacing a worn gasket stops warm air leaks and keeps food fresher.

• Forms an airtight perimeter seal around the refrigerator door to prevent air exchange
• Helps hold set temperatures and reduce condensation or sweating around the door
• Direct replacement for gaskets that are cracked, shrunken, warped, or torn
• Can address symptoms like the door not closing flush and warming in the fresh food section

• Disconnect power; let the new gasket relax at room temperature. Warming it in hot water or with a hair dryer on low can help remove kinks
• Remove the old gasket and install the new one per your model's design, seating the corners first and working evenly around the door
• If your model uses a retainer, snug screws without overtightening; ensure the gasket is fully engaged in the channel
• Close the door and check for even contact all around; adjust door alignment or hinges if needed

This part has been discontinued and is no longer available.