Parts for Maytag DG22CA: 07 - Inlet Duct, Gas Valve & Combustion Cone Parts

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Flame Sensor is an OEM replacement part for Whirlpool gas dryers. This component plays a critical safety role by monitoring the presence of the gas burner flame during the drying cycle.

Causes of needing to replace the flame sensor can include normal wear and tear over extended use, exposure to high temperatures or corrosion, or physical damage to the sensor itself.

Symptoms that may indicate a faulty flame sensor include:

• The dryer not heating or producing heat properly
• Error codes related to the gas system or ignition failure
• The dryer shutting off unexpectedly during cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models. 

The Flat Style Dryer Igniter is an OEM part for Whirlpool dryers. This essential component is responsible for igniting the gas in the burner, allowing the dryer to heat up and effectively dry your clothes. The igniter heats up to a high temperature to ignite the gas, starting the heating process necessary for drying.

Causes of a bad dryer igniter include wear over time due to repeated heating cycles, electrical failures that prevent the igniter from heating, and physical damage which can cause the igniter to break or malfunction.

Symptoms of a bad dryer igniter include:

• Dryer not heating up despite being turned on
• Gas smell indicating the gas is not being ignited
• No visible glow from the igniter area when the dryer is activated

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This burner assembly is the gas/air mixing and flame head for gas dryers. Replacing a warped or corroded burner restores reliable ignition and steady heat so loads dry evenly and cycle times return to normal.

• Mixes incoming gas with air and directs it to the igniter for proper light-off
• Produces a stable flame to heat the dryer's airflow
• Replaces burners that are bent, rusted, or clogged and affecting ignition
• Typical symptoms: no heat, burner won't light, intermittent heat, or long dry times

• Disconnect power, shut off gas, and allow the dryer to cool before servicing.
• Access the burner compartment; note component positions and wiring for reassembly.
• Protect the igniter and sensor mounted near the burner from impact.
• After reassembly, restore gas and check all connections with a leak-detection solution; verify proper ignition and flame.

This high-limit thermostat is a safety temperature limiter that helps prevent overheating in electric dryers by cutting power to the heating circuit if temperatures get too high. It's a direct-replacement style part used where the dryer needs a reliable over-temp cutoff. What it does:

• Monitors dryer heater temperature and opens the circuit if the unit overheats
• Stops the heating element from running when unsafe temperatures are detected
• Helps protect internal components and reduce fire risk from sustained over-temp conditions
• Can be a factor when the dryer won't heat or the heater cycles off prematurely

• Disconnect power to the appliance before starting any repair
• Located on or near the heater assembly; access usually requires removing the dryer cabinet or rear panel
• Handle terminals and wiring carefully; note connector positions before removal
• Test continuity with a multimeter to confirm failure before replacing

By Maytag. This three coil kit is used on older Maytag, Admiral, Norge, and Jenn Air dryers. Includes three coils - 12001348, WP305604, WP305605.

One of three coils, to get all three order 12001348

One of three coils, to get all three order 12001348

The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe and efficient conversion.

Over time or due to specific needs, you might need to convert your appliance from natural gas to LP gas. Causes for needing this conversion include moving to an area where only LP gas is available or preferring LP gas due to its efficiency and environmental benefits.

Symptoms indicating the need for a gas conversion kit include:

• Moving to a location that only supplies LP gas
• Changing energy preferences for better efficiency
• Appliances set up for natural gas needing adaptation to LP gas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Specs: 10 - 16 x .375

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts