Parts for Maytag MLG19PDAEW: 08 - Door Shroud & Door Latch Assembly (Wash) Parts

A small replacement clip that secures the dispenser hose to the dispenser assembly, helping keep the hose seated and reducing the chance of leaks or disconnection. Simple, durable part for restoring proper hose retention. What it does:

• Holds the dispenser/hose connection firmly in place to prevent the hose from slipping free
• Helps reduce water leaks and intermittent dispenser flow caused by a loose hose
• Keeps hose routing stable to avoid rubbing or wear against nearby components
• Works with the dispenser assembly to maintain proper alignment and seal

• One retainer as shown

• Disconnect power and water supply before starting any repair
• Access the dispenser area per your appliance's service instructions; remove trim or panels if required
• Snap the retainer over the hose at the dispenser connection until it seats; verify the hose is fully seated
• If you see damage to the hose or fittings, replace those parts before finishing

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This hinge kit replaces a worn or damaged refrigerator/freezer door hinge to restore proper door alignment and sealing. It helps stop door sagging and ensures smooth opening and closing for a tight temperature seal. What it does:

• Replaces a damaged or bent door hinge to correct misaligned or sagging doors
• Restores smooth hinge movement for easier opening and closing
• Helps the door seal properly to maintain internal temperature and efficiency
• Prevents rubbing or binding that can damage door gasket or cabinet finish

• Disconnect power to the appliance before beginning any repairs to avoid injury
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use basic hand tools; follow for correct alignment and torque
• After installation, check door alignment and gasket contact; adjust as needed

This factory replacement hinge screw secures the door hinge to the appliance cabinet or door. Replacing a worn or missing screw restores solid door mounting and alignment for safe, reliable opening and closing.

• Fastens the hinge securely to the door or front panel
• Helps maintain proper door alignment to prevent rubbing or sagging
• Replaces missing, stripped, or corroded hardware
• Typical symptoms include a loose/sagging door, difficulty latching, or rattling at the hinge area

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Support the door while removing and installing hinge screws
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace them together for consistent alignment

This hinge cover is a small trim piece that conceals the door hinge and mounting screws. Replace a cracked or missing cover to restore a clean, finished look and help keep lint and debris out of the hinge cavity.

• Covers and protects the door hinge and screw heads
• Restores a smooth, finished appearance around the hinge opening
• Helps shield the hinge pocket from lint and debris
• Common replacement when the original cover is cracked, missing, or loose

• Disconnect power; for gas units, also shut off the gas supply
• Support the door; loosen/remove hinge screws as needed to access the cover
• Remove the damaged cover; position the new cover and secure per model design
• Verify door closes and aligns properly before returning to service

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

A small replacement clip that secures the dispenser hose to the dispenser assembly, helping keep the hose seated and reducing the chance of leaks or disconnection. Simple, durable part for restoring proper hose retention. What it does:

• Holds the dispenser/hose connection firmly in place to prevent the hose from slipping free
• Helps reduce water leaks and intermittent dispenser flow caused by a loose hose
• Keeps hose routing stable to avoid rubbing or wear against nearby components
• Works with the dispenser assembly to maintain proper alignment and seal

• One retainer as shown

• Disconnect power and water supply before starting any repair
• Access the dispenser area per your appliance's service instructions; remove trim or panels if required
• Snap the retainer over the hose at the dispenser connection until it seats; verify the hose is fully seated
• If you see damage to the hose or fittings, replace those parts before finishing

A small replacement clip that secures the dispenser hose to the dispenser assembly, helping keep the hose seated and reducing the chance of leaks or disconnection. Simple, durable part for restoring proper hose retention. What it does:

• Holds the dispenser/hose connection firmly in place to prevent the hose from slipping free
• Helps reduce water leaks and intermittent dispenser flow caused by a loose hose
• Keeps hose routing stable to avoid rubbing or wear against nearby components
• Works with the dispenser assembly to maintain proper alignment and seal

• One retainer as shown

• Disconnect power and water supply before starting any repair
• Access the dispenser area per your appliance's service instructions; remove trim or panels if required
• Snap the retainer over the hose at the dispenser connection until it seats; verify the hose is fully seated
• If you see damage to the hose or fittings, replace those parts before finishing