Parts for Maytag MLG19PDAEW: 07 - Cabinet-Front (Washer) Parts

Specs: No.8X1/2 HEX WASHER HEAD

Specs: 10 - 16 x .375

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This pressure switch senses and signals the washer's water level so the machine fills and cycles correctly. Replacing a failing switch restores accurate water-level sensing for consistent wash performance. What it does:

• Monitors tub water level and signals the control board to start/stop filling.
• Helps the washer advance through fill, agitate, and drain cycles based on detected water height.
• Common symptom: washer overfills, underfills, or fails to advance cycles.
• Works with existing pressure hose and wiring harness to relay air pressure changes.

• Disconnect power and water to the appliance before beginning any work.
• Note and photograph hose and wiring positions before removal to ensure correct reinstallation.
• Inspect or replace the small pressure hose if cracked or clogged; ensure a tight, leak-free connection.

This clip is a small retaining fastener used to secure components inside your appliance, keeping parts aligned and in place during operation. Replacing a worn or missing clip helps stop looseness, vibration, and premature wear.

• Holds a designated part firmly to its mating surface
• Maintains proper alignment to reduce rattling and shifting during cycles
• Symptoms of failure: parts that won't stay attached, misalignment, buzzing/rattling noises, or a visibly bent/missing clip
• Restores a secure, factory-style fit

• Disconnect power; turn off water supply before servicing
• Note the original clip position and orientation (a quick photo helps)
• Use needle-nose pliers to release/install; avoid over-bending the clip
• Ensure the component is fully seated and secure before reassembly and testing

This spring support secures a suspension spring to the washer's frame, helping keep the tub stable during wash and spin. Replacing a damaged support restores proper balance control to reduce vibration and banging. What it does:

• Anchors a suspension/tub spring to the cabinet or base
• Helps control tub movement and maintain alignment during spin
• Failure can cause excessive vibration, banging, off-balance shutdowns, or a leaning tub
• Visible cracks, bent tabs, or a detached spring indicate the support needs replacement

• 1 spring support

• Disconnect power and turn off water before servicing
• Support the tub and carefully relieve spring tension before removing the old support
• Transfer the spring to the new support and install in the original location/orientation
• Wear gloves and eye protection; springs are under tension

Screw: 8-16 x 3/8 inch.

Spesc: #12 pozi - drive

Specs: 10 - 16 x .375

Specs: 10 - 16 x .375

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.