Alliance Parts

Threaded metal shaft that mounts the idler roller in dryers and washer-dryer combos. Replace if bent, worn, or stripped threads prevent secure roller installation.

Fix a washer that won't start or respond to controls with this switch assembly. Restores electrical switching in control and safety circuits.

This front bulkhead assembly forms the dryer's front drum support and air seal. Replacing a worn or damaged bulkhead restores smooth drum rotation, reduces noise, and helps maintain proper airflow for consistent drying performance.

• Supports and aligns the drum at the front to prevent rubbing and scraping
• Helps seal the lint/air path so heat stays in the drum and exhaust flows correctly
• Air leaks at the front bulkhead can contribute to long dry times or lint in the cabinet

• Disconnect power and gas supply and allow the dryer to cool before servicing
• Remove the front panel/door assembly; support the drum before detaching the old bulkhead
• Transfer any model-specific components from the original bulkhead and ensure seals/glides are correctly positioned
• After installation, rotate the drum by hand to verify clearances, then reassemble and test

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

Washer won't drain or leaves standing water after cycles? This drain pump removes water from the tub. Common repair that restores proper drainage.

Replacement timer knob assembly for dryers and washing machines. Restores control when original knob is cracked, broken, or worn. Installs on control panel.

Trunnion shaft kit for laundry center washers. Replaces worn, damaged, or broken trunnion shaft assembly. Essential structural component for drum support.

This replacement knob assembly with skirt restores a secure, easy-to-turn control interface on the appliance. It provides a finished look while allowing reliable selection of settings. What it does:

• Replaces a cracked, stripped, or missing control knob to restore user control
• Provides a stable grip and tactile feedback when turning settings
• Helps prevent accidental slips or selector misalignment caused by worn knobs
• Matches the original mounting style for a direct-fit replacement

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the old knob by pulling straight off the control shaft; install the new knob by aligning and pushing fully onto the shaft
• If the original used a retaining clip or set screw, verify and reinstall it; only use parts explicitly included

A clear silicone adhesive/sealant used to bond and seal appliance trim and components, helping restore watertight and stable assemblies. Supplies a durable, flexible hold for small repairs where factory adhesive is specified. What it does:

• Bonds trim, panels, and small plastic or metal parts to prevent movement and leaks
• Seals gaps to reduce water intrusion around housings and door areas
• Provides a flexible, durable hold that resists vibration and temperature changes
• Useful for reattaching trim, tabs, and molded parts when original adhesive has failed

• One (1) clear 3 oz tube of DOW 737 adhesive

• Use in a well-ventilated area; wear gloves and eye protection to avoid skin/eye contact
• Surface must be clean, dry, and free of oils or old adhesive for best adhesion
• Apply as a thin, even bead; allow recommended cure time before reassembling or using appliance
• Follow any OEM repair instructions and local disposal guidance for adhesive containers

Drive belt transfers motor power to spin the washer drum. Replace if agitation or spinning is weak, noisy, or fails. Verify fit by model number.

Lubricates washer seals, gaskets, and rubber parts to reduce noise and wear. Apply when parts become stiff or noisy. Verify fit with your model number.

Specialized service wrench for washer transmission and hub fasteners. Essential tool for technicians performing maintenance on specific washer models.

Fix a dryer that won't start or has no power with this transformer. Common failure part that controls voltage to operating components. DIY repair.