Alliance Parts

This pump assembly removes wash water from the tub and routes it to the household drain so the washer can complete drain and spin cycles reliably. Designed to restore proper water removal and reduce leak risk when the old pump fails. What it does:

• Forces wastewater out of the tub during drain cycles so the washer can advance to spin and finish cycles
• Helps prevent standing water in the drum that can cause odors or skipped cycles
• Can reduce abnormal noises caused by a failing or clogged pump
• Works with the washer's drain hose and plumbing to maintain proper flow

• One pump assembly

• Disconnect power and water before starting any repair
• Inspect and clear the drain hose and pump inlet before replacing the pump
• Expect basic panel and hose removal; keep screws and fasteners organized
• After installation, run a short drain/spin cycle to check for leaks and proper operation

This push button switch mounts in the appliance's control panel and sends an electrical signal to the control when pressed. Replace a worn or sticking switch to restore dependable button response and function activation. What it does:

• Panel-mounted switch that closes its contacts when pressed to signal the control
• Restores reliable front-panel input for starting or selecting a function
• Helps address no response or intermittent response when the button is pressed
• Replaces switches with loose action, sticking, or heat-discolored/burned terminals

• 1 push button switch

• Disconnect power before servicing to avoid electrical shock
• Access the console/control panel to reach the switch
• Note wire positions (take a photo) and transfer connectors one at a time; ensure firm, fully seated terminals
• Secure the switch in the panel (nut/clip as applicable), verify button action, then reassemble and test

The Lid Lock Catch Assembly is an OEM part for SpeedQueen washing machines. It is a mechanical component located on the washer lid that functions to securely latch and lock the lid shut during operation. 

Symptoms of a failing lid lock catch include: 

• The lid fails to lock firmly in place when closed
• Vibrations or movement of the lid during spinning cycles
• The inability of the washer to detect a closed lid and start cycles
• Buildup of lint or mineral deposits interfering with components

Causes of failure can be wear of moving parts over many uses, buildup that disrupts precise mechanisms, or impact damage affecting proper alignment and engagement. 

This OEM replacement is also compatible with Alliance, American, Continental, and some Kenmore models. 

This limit thermostat monitors dryer temperature and opens the heating circuit if temperatures climb too high, helping protect the appliance and laundry. Replacing a failed thermostat restores reliable heat and safe temperature control. What it does:

• Monitors temperature at the heater/blower housing and opens at its limit to prevent overheating
• Helps maintain safe drying temperatures during normal cycles
• Common symptoms of a failed thermostat: no heat or intermittent heat, dryer runs too hot/overheats, or cycles end early due to overheating

• 1 limit thermostat

• Disconnect power and, if applicable, shut off gas before servicing
• Access the thermostat location per your model (typically on the heater housing or blower duct), remove mounting screws, and note wire positions
• Transfer wires to the new thermostat and mount it flush for proper sensing
• After reassembly, clear lint and verify venting/airflow to prevent repeat overheating

This 3-position fabric selector switch is the control behind the knob that lets you choose the fabric setting on your unit. Replacing a worn switch restores positive detents and ensures your selection is recognized instead of ignored or stuck.

• Provides three selectable fabric settings to tailor operation
• Routes the chosen setting to the timer/control
• Typical symptoms: no response when changing settings, intermittent selection, or being stuck on one mode
• Physical clues of failure: loose/no detent feel, broken shaft, or heat-discolored terminals

• Disconnect power before servicing
• Access the control console; remove the knob and retaining hardware to free the old switch
• Photograph/label wire positions and transfer each lead to the same terminals on the new switch
• Reassemble and test all three positions for proper engagement

This water inlet mixing valve controls and blends the hot and cold water entering your washer for proper fill temperature and water level. A worn valve can cause fill problems or unwanted leaks into the tub.

• Regulates hot and cold water flow to achieve the selected temperature
• Opens and closes electrically during fill cycles
• Common symptoms: slow fill, no fill, fills with only hot or only cold, or water seeping into the tub when the washer is off
• Electrical coil-operated design for reliable operation

• Unplug the washer and shut off both water supplies before servicing
• Place a towel or pan to catch residual water when disconnecting hoses
• Note hose positions (hot/cold) and wire connectors for correct reassembly
• After installation, check for leaks and run a test fill cycle

Considered a crucial part of the dryer, the blower fan assembly is the part that pulls in air from outside and then circulates that air in the drum to ensure clothing gets dry. After the air is moved around the drum, it is then moved through the exhaust vent. This part is located on the motor shaft and is made of durable plastic. Regular use can lead to wear and tear or damage to this component. If this occurs, the air in the dryer may not dry the clothing. In this case, the blower fan assembly will need to be replaced.If the blower fan assembly needs to be replaced, first the dryer should be unplugged from power. Take the cabinet top off and remove the front panel on the appliance. Take out the drum, remove the motor clamp, and loosen the blower fan so it can be removed. Take it out and replace it with the new blower fan assembly.The blower fan assembly is designed to be used with dryers manufactured by Amana and Speed Queen. It is sold as an individual part. This is an authentic OEM replacement part that is sourced directly from the manufacturer.

This drive motor and pulley assembly powers the belt-driven system to rotate the drum or tub. Replacing a weak or seized motor restores consistent rotation and reliable cycle performance on compatible 120V/60Hz models. What it does:

• Drives the belt that turns the drum or tub for wash/spin or tumble
• Provides correct 120V/60Hz operation for North American units designed for this spec
• Helps address symptoms like humming with no start, drum/tub not turning, belt not moving, or burning/motor smell
• Replaces a worn pulley to improve belt tracking and reduce slippage or squeal

• 1 motor and pulley assembly

• Disconnect power before servicing; for gas units, also shut off gas supply
• Relieve belt tension, note routing, and transfer wiring/connectors from the old motor
• Align the pulley and set proper belt tension; rotate by hand to verify free movement before restoring power

Note: DO NOT use any sealant other than 200996P Sealant.

The Belt is an OEM part for Speedqueen washers. Transmits power between the motor and pulley system to turn the basket. Without a functioning belt, the washer will be unable to properly rotate the drum and agitate laundry during cycles.

Causes of a bad belt can include cracking, stretch wear or fatigue caused by age, prolonged use or excessive loads. Damage may also be due to slipping off pulleys.

Symptoms of a bad Belt include:

• Noise or squealing coming from the drive area
• The basket or agitator not spinning or turning slowly
• Motor overheating due to increased load from a slipping belt
• Belt slipping off or breaking completely

The Timer is an OEM part for SpeedQueen washing machines. It controls the duration of the wash cycles, ensuring each phase of the cycle is completed in the correct sequence. This includes washing, rinsing, and spinning, providing precise control over the washing process for optimal results.

Over time, the timer can become faulty due to electrical issues, wear and tear from repeated use, or internal component failures. When the timer malfunctions, it can disrupt the washing machine's ability to complete cycles correctly.

Symptoms of a bad timer include:

• The washer not advancing through cycles
• Cycles that are too long or too short
• The machine stopping mid-cycle
• Inconsistent or erratic timing of cycle phases

This OEM part ensures reliable performance and compatibility with SpeedQueen washing machines.

This timer knob assembly replaces a worn or broken control knob so you can confidently select and adjust cycles. A fresh knob restores a positive grip on the timer shaft and smooth, accurate operation.

• Mounts on the timer shaft to turn and set cycle selection and time
• Restores secure engagement when the original knob is cracked, stripped, loose, or missing
• Helps ensure the timer turns when you rotate the knob
• Common symptoms: knob spins without engaging, difficult to set cycles, visible damage

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft; avoid prying that could damage the control
• Align the new knob with the shaft (flat/D-shape) and press until fully seated
• If the original used a small insert or spring clip, transfer it to the new knob if needed

This terminal block assembly connects your dryer's power cord to the internal wiring, providing a secure, heat-resistant junction. Replacing a damaged block restores a reliable electrical connection and helps prevent intermittent power, overheating, or burnt terminals.

• Provides an insulated junction point between incoming power and the appliance's internal wiring
• Secures cord conductors with screw terminals to maintain a tight, low-resistance connection
• Helps resolve issues like the dryer not powering on, intermittent shutdowns, or a burning smell near the cord cover
• Replaces cracked, melted, or stripped terminals to restore a safe power path

• Disconnect power at the breaker before servicing
• Photograph/label wire positions and move one wire at a time to the new block
• Tighten terminal screws firmly; recheck connections after initial operation
• Inspect/replace any heat-damaged cord lugs, wiring, or strain relief before reassembly

The Timer is an OEM component specifically designed for Speed Queen commercial washers. It plays a crucial role in controlling wash cycle times and sequences. 

The timer allows for precise regulation of cycle segments to ensure laundered items receive optimal cleaning. It advances operations through the wash, rinse, and spin periods.

Causes of a bad timer can include issues with the electronic circuit board, worn contacts and connections, or faulty input and output switches.

Symptoms of a bad timer include:

• Abnormal cycle lengths that under or over-clean clothes
• The washer fails to advance to subsequent cycles  
• Unexpected stopping or pausing during operation

This OEM Speed Queen replacement part is also compatible with Dexter, Huebsch, Milnor, and IPSO commercial washer models.
 

This white timer knob replaces a cracked or missing knob so you can reliably set your laundry cycles again. It mounts on the timer shaft to restore a secure, easy-to-grip control for selecting cycles.

• Engages the timer shaft so you can set and adjust cycle time/settings
• Restores positive feel and control when turning the timer
• Common symptoms: cracked or stripped knob; spins without moving the timer
• Additional signs: loose or missing knob; hard to turn; falls off

• Disconnect power before service
• Pull the old knob straight off the timer shaft; transfer any retaining clip/insert from the old knob if present
• Align the new knob with the shaft and press until fully seated
• The knob turns the timer smoothly

This timer skirt is the bezel that sits behind the timer knob on the control panel. It replaces a cracked or missing ring so you can securely turn the knob and select settings.

• Sits around the timer shaft as the cosmetic/structural ring behind the knob
• Supports and stabilizes the timer knob during setting selection
• Replaces a cracked, warped, or missing bezel that causes a loose or wobbly knob
• Typical symptoms include a broken ring, misaligned knob, or difficulty selecting settings

• Disconnect power before servicing
• Pull off the timer knob; remove any retaining clip or nut if present
• Remove the old skirt; align and seat the new skirt in the control panel
• Reinstall the knob and verify smooth operation