Amana Dishwasher Gasket & Seal

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Located between the console and door

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Note: For faucet adapter

The Seal is an OEM part for Whirlpool dishwashers. As a crucial door component, it ensures a tight fit that prevents leaks and contains the necessary heat and moisture during operation. 

Symptoms of a bad seal can include cracks, tears, or looseness allowing water to escape during cycles. Deterioration from chemical exposure or repeated flexing over time is common.

Causes of a bad seal include general wear and tear, damage from improper loading of dishes, or accidents like sharp objects puncturing the material.

Symptoms of a bad seal include: 

• Puddles or pools of water found beneath the dishwasher after cycles
• Wet floors and surfaces surrounding the dishwasher  
• Steam or moisture visible escaping during heating phases
• The door not closing or latching properly

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Dishwasher Door Seal is an OEM replacement part for Whirlpool dishwashers. It provides a tight seal around the dishwasher door to prevent water, sound, and heat from escaping during the wash cycle. Measuring 71” in length (and stretching up to 75”), this door seal prevents water from leaking out during wash cycles.

Causes of a bad seal can include cracks, tears, or splits that develop due to regular use and age. Damage may also occur from over-tightening of the door or accidental impact.

Symptoms of a bad dishwasher door seal include:

• Water or moist air leaks around the door during a cycle  
• Higher energy bills due to hot air escaping
• Excess moisture or mineral deposits around the door seal area
• Food particles or debris trapped under a torn seal

This genuine OEM Whirlpool replacement seal is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement pump gasket with silicone sealing material that restores a watertight seal between the pump and housing. Helps stop leaks at the pump area and prevents water pooling under the appliance.

• Seals the pump to the housing to help prevent water leaks and drips.
• Common repair for visible water under the appliance or leaks coming from the pump area.
• Silicone sealing material provides a flexible, water-tight interface that conforms to the pump housing.
• Designed to replace the factory pump gasket for a direct fit and proper sealing.

• Disconnect power and water supply before beginning any repair.
• Remove the pump assembly to access and replace the gasket.
• Clean and dry mating surfaces before installing the new gasket; seat evenly to ensure a full seal.

This O-ring creates a watertight seal in your dishwasher's wash or drain system, helping prevent leaks and maintain proper water pressure. Replace a brittle, flattened, or damaged ring to restore a reliable, leak-free connection.

• Provides a watertight seal between mating parts such as pump housings, fittings, or hose joints
• Helps stop drips and seepage caused by a worn or deformed seal
• Common symptoms: water under the unit, moisture around pump/tubing connections, or leaks after reassembly
• Replace if the old ring is cracked, cut, flattened, or hardened

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water
• Clean the groove and mating surfaces; lightly moisten or use a manufacturer-approved lubricant to help the ring seat without pinching
• Seat evenly, reassemble without overtightening, and run a short test cycle to check for leaks