Amana Gasket & Seal

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

My Whirlpool dishwasher was leaking out the bottom of the door. I replaced the gasket and the lower door seal. When I ran a test wash, it was still leaking. After reading more online, I found that it could be a cracked washer arm. The initial inspection of the washer arm looked normal but when I used my faucet to slowly pour water into the inlet of the arm, I noted that water was leaking through a seam and not just the holes where it should come out. I then tried running a wash without the... Read more

• Marks left on clothes

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

• Marks left on clothes

Maytag Gas Dryer Model: MGDE300VW1 I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow! Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts... Read more

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Takes too long to dry
• No heat or not enough heat

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

The tray was simple, pick up the old one, pop in the new one. The gasket for my refrigerator was almost as easy. When I received the part I opened it up and let it lay flat for about 3 days (probably overkill). The old gasket popped right out and the new one went in really easy. The entire job took me about 10 minutes to do, no tools required. I do recommend that you start with corners and work your way to the middle of each side. I found that would prevent any stretching. You also need to... Read more

The rubber seal/gasket was torn on our KitchenAid refrigerator right side door. I purchased the replacement and followed the directions/recommendations of how to prepare the new gasket for installation. When it's removed from the shipping box, it does have wrinkles and preparing it is a must. I set it out on our tile floor and then used a heat gun (low setting) to warm it up and massage it. It took me about 15 minutes, stopping and restarting as I let the rubber come back to it's desired shape.... Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

• Marks left on clothes

Remove Top of washer Remove Top bracket that covers soap dispenser Disconnect plug that leads to the front control panel Remove 3 screws from underneath the bottom kickplate, remove kickplate Remove 2 screws holding Door, remove door Remove screws holding the front of the machine Using long Phillips screwdriver, loosen the screw that connects the metal wire band that encircles the rubber baffle on the Tub side, remove band Using needle nose pliers, remove the door side baffle ring by pulling... Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

Did some online research and everything pointed to the fact that moisture was getting into the freezer and therefore the seal was not doing it's job. I ran my finger along the seal and sure enough I detected cold air coming out of one corner of the seal. I ordered the appropriate part from Appliance Parts Pros (APP) but decided to test my diagnosis by installing thin weather stripping in the affected area. I checked the freezer the next day and saw no accumulation of any more Rime ice so... Read more

• Leaking

I thought it was the gasket so I ordered a new one. While waiting for it to arrive I read some other forums where I read that sometimes the air vent on the front could be dirty and cause leaking. I popped out that vent cover and it was clogged. Using an old toothbrush and a tiny paint brush I cleaned all of the gunk out. No more leak even with the old gasket in place. I'll save the new gasket for when I need it in the future. Read more

I determined that the gasket was pinched, leaking at corner. Ordered new gasket from this site (easy find with part diagram). Removed old gasket, replaced with new. Read more