Amana Dryer Parts

Replace your dryer's damaged, dented, or cracked outer door panel. This finished surface panel installs on the front door assembly to restore appearance.

Fix a dryer that won't heat or has a weak flame with this gas burner orifice. Controls proper fuel flow for consistent heating. Direct replacement part.

This finished burner funnel directs gas and air into the burner for correct flame shape and ignition. It replaces a damaged or corroded funnel to help restore even heating and reliable burner performance. What it does:

• Channels gas and air into the burner for proper mixing and flame distribution
• Helps maintain even flame across the burner for consistent cooking heat
• Can reduce ignition delays or uneven flames caused by a damaged funnel
• Works with the burner assembly; not a standalone gas valve or igniter

• Turn off gas supply and electricity to the appliance before servicing
• Replace only with the correct funnel for your burner; follow OEM diagram for orientation
• Tighten fittings by hand-first, then snug—do not overtighten; inspect for leaks after reassembly

13 oz. enamel spray paint in biscuit color for appliances. Restores scratched, chipped, or discolored surfaces on refrigerators, dishwashers, and more.

Fix a dryer that won't heat or stops mid-cycle with this thermal fuse and thermostat kit. Restores overheat protection. Moderate DIY repair.

Dryer won't heat or stops when hot? A faulty cycling thermostat disrupts temperature regulation. Testing with a multimeter confirms the issue.

This touch-up paint bottle restores small chips and scratches on painted appliance surfaces to improve appearance and help protect against rust. Easy-to-apply formula matches common appliance finishes for quick cosmetic repairs. What it does:

• Covers small chips, nicks and surface scratches to improve appearance
• Helps protect exposed metal from moisture and surface corrosion after damage
• Provides a precise application for targeted repairs on doors, panels and trim
• Can be used on painted steel and metal appliance surfaces (test in an inconspicuous area first)

• Clean and dry the repair area; remove loose paint and corrosion before applying
• Shake bottle well and apply sparingly with included applicator or a small brush
• Allow adequate drying time between coats and follow any manufacturer cure instructions on the label
• Wear gloves and work in a well-ventilated area; keep away from open flame and out of reach of children

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.

This is a white rotary control knob that attaches to the dryer's selector or timer shaft, allowing you to choose cycle settings. It fits over a D-shaped shaft and snaps or pushes into place. Replace this knob if it is cracked, broken, or the shaft grip has worn out so the knob spins without engaging the control.

Sealer for refrigerant line insulation.

Replacement mounting screw for securing appliance panels, trim, and internal components. Restores proper fastening when original screws are missing or stripped.

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten

Size: 1/4 lb.