Amana Refrigerator Parts

Replaced the ice level arm Read more

Replaced filter housing ,flushed water lines. Read more

• Leaking

I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more

• Won't start

Tried to put refrigerator in defrost mode and defrost would not initiate. Checked the bi-metal and heater, both tested good. Replaced the ADC board and refrigerator went in to defrost. problem solved. Read more

My husband followed the instructions on the video. Read more

Let the gaskets straighten out a bit overnight. Pulled out the old gasket, Cleaned and dried the area well though almost all the mold was in the old gasket. Pressed in the new gasket. Use a hairdryer to warm up and press the slightly deformed areas of the gasket into place. Quick and EASY. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

Removed the worn gasket, cleaned the door, snapped on the new gasket. Read more

Removed the old tube. You will need this part - note that it might look different from what you have because they redesigned the part to not have a sharp curve at the bottom part where it plugs into the valve. You will also need a 5/8" stainless steel hose clamp (that will go down to 1/4") to clamp the top part of the hose that feeds into the icemaker (this replaces the factory clamp that is effectively throw-away). Read more

It was not hard at all to replace our refrigerator door gasket. First I found appliancepartspros.com because I was looking up on YouTube how to do the replacement. Your video was excellent and showed me that I indeed could perform the job. I had a question about the replacement door gasket and emailed your service team at the end of the day. By next morning you had replied with the actual part number for the gasket. Shipping was fast. I had watched the video several times and so performed... Read more

Replaced with parts ordered. Read more

First had to clean inside the empty freezer, that was the hard part. removed old gasket and cleaned inside the track in the door. had the new gasket well warmed and in the right shape. put new gasket in track. seating it firmly. It was very easy. I did watch a couple of online videos to get the general idea of what it detailed. While I was at it I cleaned the coils with the brush I also bought with the gasket, worked great. all in all if you get organized before hand and take your time,... Read more

Replaced the actuator pad on the Whirlpool Gold Series, releasing the electronic menu pad to get to the water activator pad was the biggest hurdle. The release tabs are underneath the menu pad and you may feel as if you may break them when releasing them. They did not break but I did hold by breath. Read more

• Ice maker not making ice
• Leaking

Replaced it Read more

• Door sweating

New seal, old one pulled out easy and new one pushed into place. Read more

Read most possible causes on AppliancePartsPros website. After deciding on a course of action, I ordered the parts with expedited shipping, received them next day, installed them on same day received and everything is working fine. Congratulations to them for possessing and offering such an excellent diagnosis tool for the DYIer. It has worked well for me many times in the past. I would never hesitate to recommend them as I feel they are a first rate organization. P.S. - Their excellent... Read more