Amana Refrigerator Parts

Small door bin mounts on the inner refrigerator door panel for organized storage. Replaces cracked, loose, or missing bins to restore usable space.

Replacement hinge pin that acts as the pivot point for your refrigerator door. Install when the original pin is worn, broken, or missing.

This ice deflector guides ice cubes from the icemaker into the ice bin to help keep ice delivery consistent and reduce cube jams or spills. It's a simple replacement that restores proper ice routing in compatible refrigerators. What it does:

• Directs ice cubes from the icemaker into the ice bin for orderly dispensing
• Helps prevent ice clumping and blockages that can stop ice flow
• Keeps ice moving away from the icemaker assembly and into the bin
• Restores proper alignment and function after a cracked or missing deflector

• Disconnect power to the refrigerator before servicing to avoid electrical or mechanical injury
• Remove the ice bin or access panel per your model's service instructions to reach the deflector
• Part typically snaps or slides into place; reuse existing fasteners unless new hardware is supplied
• After installation, reconnect power and run the icemaker through a cycle; discard any ice made during the repair if contamination is suspected

Fixes frost buildup on evaporator coils and inconsistent cooling. This refrigerator defrost heater melts ice during defrost cycles. 20-minute repair.

Mounts in the dispenser to secure the ice housing assembly. Keeps the chute and door aligned for smooth dispensing. Replace if cracked, broken, or worn.

Dryer stops early on auto cycle but works on timed? The moisture sensor control board monitors dryness levels. DIY-friendly repair, 15-20 minutes.

Replace a cracked, yellowed, or missing fresh food door handle on your refrigerator. This white handle installs on the main compartment door for secure grip.

Replacement roller axle support shaft for refrigerators. Installs to support rotating assemblies. Replace when worn, damaged, or causing wobble.

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

Size: 7 foot long.

This decorative panel covers the bottom front of your refrigerator, hiding the compressor and mechanical components underneath. It snaps into place at the base of the unit and provides a finished appearance. Replace this grille if it's cracked, discolored, or missing, as it also helps direct airflow for proper cooling.

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Seals your freezer door to maintain cold temperatures and prevent frost buildup. Replace when worn, cracked, or loose to restore efficiency. Confirm fit with your model number.

This is the chute component that directs water from the fill tube into the ice maker mold inside the freezer compartment. It ensures water flows accurately into the ice tray without spilling into the surrounding freezer area. Replace this part if water is leaking around the ice maker, ice forms outside the mold, or the chute is cracked or blocked with ice buildup.

Replaces a broken or worn top left door hinge on your refrigerator. Secures the door to the cabinet for proper alignment and smooth pivoting movement.

Fixes frost buildup in freezer and warm fridge temps. This defrost heater melts ice from evaporator coils to restore proper cooling in 30-60 minutes.