Parts for Kenmore 663.48(1988) (66348(1988), 663 48(1988)): Backguard Section Parts

Decorative bezel ring that fits around your range's burner control knob. Replace if cracked, discolored, or missing to restore a clean appearance.

This part has been discontinued by the manufacturer and is no longer available.

Range fluorescent light not working? This left-side light receptacle socket restores proper electrical connection. Common fix for flickering or dead lights.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Decorative nut for gas range exterior trim. Secures cosmetic panels and trim pieces. Replace if lost, stripped, or corroded for a clean finish.

Control shaft for gas ranges. Connects control knobs to valves. Replace if broken, stripped, cracked, or missing to restore knob operation.

Left endcap for gas ranges. Covers and finishes the exposed end of your cooktop or control panel. Replace if cracked, broken, or missing.

If your gas range oven won't heat after a power outage or surge, a blown thermal fuse may be the cause. This safety device prevents overheating damage.

This elbow is a threaded pipe fitting that redirects and secures a fluid line connection where space or alignment requires a 90° turn. It provides a compact, threaded junction to connect compatible appliance tubing or hose to a valve or port. What it does:

• Connects two threaded line ends at a 90° angle for tight routing in confined spaces
• Provides a sealed, threaded junction between a 1/2 in. NPT inlet and a 9/16-24 threaded outlet
• Helps stop leaks and maintains proper line alignment when the original elbow is worn or damaged
• Commonly used where a bent or cramped connection prevents a straight coupling

• One elbow fitting (1/2 in. NPT x 9/16-24)

• Turn off and depressurize the water supply (or system) before removing or installing fittings
• Start threads by hand to avoid cross-threading; tighten with appropriate wrench until snug
• Use plumber's tape or thread sealant only if specified by the appliance manufacturer

Black hinge washer for electric and gas ranges. Replaces worn, cracked, or missing washers on door hinges to ensure proper door alignment and support.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Rubber bumper that cushions the range door or drawer when closing. Replace if cracked, worn, or missing to prevent rattling and protect surfaces.

Range door latch shield that covers and protects the top latch mechanism. Replace if cracked, broken, or missing to restore proper door alignment.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Pressure regulator for gas ranges. Controls gas flow from supply line to burners and oven. Replace if worn, damaged, or causing pressure issues.

Sound dampening insulation for gas ranges. Installs inside the range cavity to reduce noise and provide thermal protection. Replace if worn, torn, or missing.

Support plate that mounts to the bottom of your range oven cavity. Replace if the original plate is cracked, warped, or damaged from heat exposure.

By Frigidaire. Fits some Frigidaire and Tappan stoves. Snap-in style.

Specs: 8 - 18 x 0.500

Gas burner won't light or clicks but doesn't ignite? Replace the igniter switch to restore spark and reliable lighting. Simple 15-30 minute DIY fix.

Secures the oven bottom panel in place. Replace if screw is stripped, missing, or no longer holds the panel securely. Sold individually.

Oven won't light even though igniter glows? Burner lights only when valve is tapped? Replace the dual gas safety valve. DIY install in under 1 hour.

Oven won't heat, slow to reach temperature, or glows dull orange? This igniter fixes weak ignition. Moderate DIY repair with basic hand tools.

Gas burners won't ignite? A faulty spark module may be the issue. This part sends electrical current to igniters. DIY-friendly, takes minutes.

Oven won't light or ignites with a loud pop? A faulty igniter is usually the cause. Simple DIY fix—disconnect two screws and wire nuts to replace.