Parts for Ge DNCD450EG7WC: 01 - Backsplash, Blower & Motor Assembly Parts

Support plate that mounts behind the dryer control panel. Replace if cracked, broken, or missing to properly secure the control assembly and switches.

This is a threaded fastener used to secure panels and small assemblies on compatible appliances, restoring a tight fit and stable operation. It replaces missing or stripped screws to reduce vibration and rattling. What it does:

• Secures trim, panels, and internal components where an 8-18 thread screw is specified
• Restores proper alignment to reduce rattles or vibration caused by loose parts
• Replaces missing or damaged screws that prevent parts from fastening correctly
• Works wherever an 8-18 x 7/16 screw is required by the manufacturer

• Use the correct screwdriver or nut driver to avoid cam-out and stripped heads
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power and remove any panels per manufacturer instructions before servicing
• If threads are damaged, replace the mating fastener

Mounting screw for refrigerators, dryers, and washers. Replaces lost, stripped, or corroded screws during repairs or part installations.

Fix a dryer that won't start, has flashing cycle lights, or runs without stopping. This electronic control board restores normal cycle operation.

This wiring harness is the factory-style electrical connector assembly that restores secure, routed connections between appliance components for reliable operation and safe power delivery. It replaces damaged or worn wiring that can cause intermittent or lost function. What it does

• Re-establishes electrical connections between controls, motors, switches, or sensors.
• Helps stop intermittent power, control failures, or components that won't operate due to broken wiring.
• Keeps wiring routed and secured to prevent chafing or short circuits.
• Provides OEM-style connectors for a direct-fit replacement when the original harness is damaged.

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the harness.
• Compare the new harness to the old one to ensure connector types and routing before installing.
• Route and secure the harness away from heat and moving parts; avoid pinching or sharp bends.

Replacement screw for securing dryer components like drum supports, panels, and housings. Needed when screws are lost, stripped, or damaged during repair.

Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

Metal bracket that secures the dryer motor and blower assembly in place. Replace if your mounting bracket is cracked, broken, or causing loose components.

Secures the ground wire to the dryer cabinet for safe electrical connection. Replace if missing, stripped, or corroded to restore proper grounding.

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Maintains tension on your dryer's drive belt. Replace if pulley is cracked, worn, or making noise. Installs inside drum assembly for smooth operation.

Replaces a cracked, rusted, or disconnected exhaust duct that routes hot air from your dryer to the home vent. Restores proper airflow and venting.

Dryer won't heat, overheats, or shuts off mid-cycle? A faulty cycling thermostat often causes these issues. Easy DIY fix with our video guide.

Hex washer-head screw secures dishwasher brackets, shields, and panels. Replace stripped, missing, or damaged screws to restore tight fit and stability.

Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.

This motor plate is the stamped metal mounting plate that secures the motor assembly and keeps it aligned for smooth operation. It restores proper motor positioning and reduces vibration-caused noise or wear. What it does:

• Provides a stable mounting surface for the motor assembly
• Maintains motor alignment to ensure smooth shaft rotation
• Helps reduce excess vibration and noise from a loose or damaged motor support
• Supports related components so belts and pulleys track correctly

• Disconnect power before starting any repair to avoid shock or injury
• Installation requires basic hand tools and access to the motor compartment
• Verify motor and surrounding hardware are undamaged; replace any worn fasteners

Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.

Hex washer-head screw secures dishwasher brackets, shields, and panels. Replace stripped, missing, or damaged screws to restore tight fit and stability.

Factory replacement screw for securing dryer panels, brackets, and components. Restores lost or loose hardware to eliminate rattling and ensure proper fit.

Replacement screw secures dryer panels, brackets, and internal components. Replace stripped, lost, or damaged screws to eliminate rattles and maintain assembly.

Dryer won't start, stops mid-cycle, or runs backward? The drive motor powers drum rotation. Moderate difficulty repair requires disassembly. Video guide.

Dishwasher won't start or runs intermittently? A faulty door interlock switch prevents operation when the door latch fails. DIY repair in 20 minutes.

Set of 12 size 8-18 mounting screws for dishwashers. Replaces lost, stripped, or missing screws for secure installation of handles and components.