Parts for Ge DSKS433EB7WW: Backsplash Cabinet Front Panel Parts

Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.

Dryer won't power on or trips breaker? Replace the terminal block and ground strap assembly to restore safe electrical connections. Easy DIY repair.

This oven door guide helps keep the oven door aligned and sliding smoothly for reliable opening and closing. It replaces a worn or broken guide to restore proper door movement and reduce rubbing or binding. What it does:

• Guides and supports the oven door along its track for smooth operation
• Prevents door misalignment that can cause scraping, uneven closing, or gaps
• Restores proper door travel when the original guide is cracked, worn, or missing
• Helps maintain an even seal by keeping the door correctly positioned

• One oven door guide

• Disconnect power to the range before starting any service to avoid shock or injury
• Support the oven door or follow the manufacturer's door-removal steps when replacing the guide
• Use only the specified replacement guide and fasteners; tighten hardware to the manufacturer's recommendations

10-16 x 1-1/4 inch screw for securing dryer panels, brackets, and internal components. Replace missing, stripped, or damaged screws during repairs.

If your dryer's control panel is exposed or electronics aren't working properly, this control shield assembly protects and secures control components.

White inner door panel for dryers. Replaces cracked, broken, or discolored inner door components. Direct fit for compatible dryer models.

Dryer won't advance through cycles or stops mid-cycle? A failing timer disrupts cycle timing and start/stop control. Moderate difficulty replacement.

This is a flexible rubber or felt seal that fits around the perimeter of the dryer door opening. It creates an airtight seal between the door and the drum area to keep heated air inside the dryer during operation. Replace this gasket if you feel hot air escaping around the door, notice longer drying times, or if the seal is torn, flattened, or deteriorated.

Dryer won't start or humming when you press start? The door switch signals when the door is closed. Easy 15-minute DIY repair with basic tools.

Outer decorative trim panel for your dryer control area. Replaces cracked, dented, or discolored panels to restore appearance and protect controls.

Seals the gap between drum and bulkhead in your dryer. Replace when worn to eliminate scraping noises, prevent fabric snags, and maintain airflow.

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance. 

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching. 

Symptoms of a bad Door Latch include:

• The dryer door doesn't stay closed during cycles.
• Difficulty in starting the dryer due to the door not activating the safety switch.
• Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Supports the front drum edge for smooth rotation. Replace when you hear squeaking or scraping sounds. Confirm fit with your dryer model number.

Dryer won't start when you press the button, or stops when released? The push-to-start switch often fails. Easy 20-minute DIY repair with video.

A front bracket that supports and secures the appliance's front panel or control assembly to restore proper alignment and stability. Replaces a worn or damaged bracket to reduce panel movement and rattling. What it does:

• Provides structural support for the front panel or control console so panels stay aligned.
• Secures trim and assemblies to prevent vibration, rattling, or loose panels.
• Restores proper fit and contact points that can affect door or panel operation.
• Helps maintain safe, stable mounting for front-facing components.

• One front bracket.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Confirm correct bracket location and orientation before fastening; use original screws or hardware.
• Do not force parts; if fitment is tight, check for obstructions or bent mounting tabs.

The dryer drum bearing and felt kit includes the rear drum support bearing and the felt seal that lines the front of the drum, keeping it centered and allowing it to spin smoothly without scraping against the dryer cabinet. These two components work together to support the weight of the drum and prevent metal-on-metal contact. If your dryer is making a loud squealing, squeaking, or thumping noise during operation, worn drum bearings and felt are among the most common causes.

Supports the front rim of your dryer drum for smooth, quiet rotation. Replace when you hear scraping or squealing to restore proper drum support.

Protective cover for your dryer's lint trap that prevents objects from entering the vent. Replace if cracked or broken. Snaps into place. Confirm fit.

Captures lint and debris from dryer exhaust to prevent vent clogs and fire hazards. Replace if damaged, cracked, or no longer sealing properly.

Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.

Protective cover for your dryer's lint trap that prevents objects from entering the vent. Replace if cracked or broken. Snaps into place. Confirm fit.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

Dryer timer knob control for selecting drying cycles. Replace if your original knob is cracked, broken, stripped, or missing from the control panel.

Cracked or loose dryer control knob making cycle selection difficult? This knob and clip assembly restores secure turning and reliable cycle control.

This is a plastic selector knob that comes with a retaining clip, used on the washer's control panel to select cycle settings. It attaches to the control shaft and allows you to choose wash cycles and options. Replace this knob if it is cracked, broken, or if the clip has snapped, causing the knob to spin freely or fall off the shaft.