Parts for Ge DSKS333EC6WW: Backsplash, Cabinet & Front Panel Parts

This cord set is a direct-replacement power cord that restores electrical connection to the appliance, letting it receive safe, consistent power when the original cord is damaged or worn. What it does:

• Provides the appliance's main AC connection so it can power on and operate
• Replaces frayed, cut, or melted cords that cause intermittent power or arcing
• Prevents unsafe wiring conditions from exposed conductors or loose connections
• Restores a secure plug/cable interface when the cord or plug is damaged

• One replacement cord set

• Always disconnect power at the breaker or unplug the appliance before replacing the cord
• Verify the replacement cord matches the original in wire count, connector type, and amp rating
• Tighten terminal screws securely and route the cord to avoid pinching or contact with hot components

The Timer Resistor is an OEM part for GE dryers. It works in conjunction with the dryer's timer to regulate the duration of the drying cycle, ensuring that clothes are dried for the appropriate amount of time.

Causes of a bad timer resistor can include electrical surges, prolonged exposure to high temperatures, or general wear over time. These factors can result in the resistor losing its effectiveness or failing completely.

Symptoms of a bad timer resistor include:

• The dryer running for too long or too short a time
• Inconsistent drying times
• The timer not advancing or getting stuck
• The dryer not starting or shutting off prematurely

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This oven door guide helps keep the oven door aligned and sliding smoothly for reliable opening and closing. It replaces a worn or broken guide to restore proper door movement and reduce rubbing or binding. What it does:

• Guides and supports the oven door along its track for smooth operation
• Prevents door misalignment that can cause scraping, uneven closing, or gaps
• Restores proper door travel when the original guide is cracked, worn, or missing
• Helps maintain an even seal by keeping the door correctly positioned

• One oven door guide

• Disconnect power to the range before starting any service to avoid shock or injury
• Support the oven door or follow the manufacturer's door-removal steps when replacing the guide
• Use only the specified replacement guide and fasteners; tighten hardware to the manufacturer's recommendations

This shield control is an electrical shield and control assembly that protects and secures the appliance's control electronics while helping ensure reliable operation. It replaces a worn or damaged shield to restore proper protection and alignment of the control components. What it does:

• Covers and shields control circuitry and wiring from debris, moisture, and physical contact
• Secures control components in the correct position to prevent loose connections
• Helps reduce risk of shorting or intermittent electrical faults caused by exposed electronics
• Common symptom: visible damage, cracked or warped shield, or control connections that appear loose

• One shield control assembly

• Disconnect power to the appliance before accessing controls to avoid shock or injury
• Handle the control area carefully and avoid touching circuit boards or connector pins
• Inspect connectors and wiring for damage; replace or reseat connectors as needed for proper fit

This timer and harness kit controls the sequence and duration of your dryer's cycles. Replacing a failing timer restores predictable cycle advancement and dependable start/stop operation so the dryer runs and shuts off on the settings you select.

• Advances the dryer through timed and automatic cycles
• Routes power to motor/heating circuits based on the cycle chosen
• Pre-terminated harness ensures correct, secure connections to the timer
• Common symptoms: timer won't advance or end, runs only on some settings, stops mid-cycle, or won't start when set

• Disconnect power by unplugging the dryer or switching off the circuit breaker
• Access the control panel; remove knob/dial if present and unfasten the old timer
• Move wiring connection-by-connection to the new timer/harness; route away from hot or moving parts
• Reassemble, restore power, and test cycle advancement

This door gasket seals the fridge/freezer door to maintain proper temperature and efficiency. Replaces a worn or torn seal to help reduce frost buildup and prevent cool air loss. What it does:

• Creates an airtight seal around the door perimeter to keep cold air in and warm air out.
• Helps prevent frost and ice buildup inside the compartment.
• Reduces compressor run time and helps maintain consistent internal temperatures.
• Common symptoms: visible gaps, torn or compressed seal, noticeable temperature fluctuations, or excess frost.

• Disconnect power before starting and work with clean, dry hands.
• Remove the old gasket by loosening retaining screws or pulling from the channel as applicable; inspect the channel for debris.
• Align the new gasket evenly and press into the door channel, working around the perimeter to ensure full contact.
• If needed, soften the gasket with warm water or a low-heat source per OEM guidance to help seat corners; avoid open flames.

This front panel is the outer decorative trim that restores the appliance's appearance and protects the control area. It gives a clean, finished look while helping keep controls and internal components shielded from spills and damage. What it does:

• Replaces a cracked, dented, or discolored front face to improve appearance
• Protects underlying control assemblies and wiring from spills and debris
• Helps align and secure control components and door/hinge interfaces
• Reduces drafts and gaps at the appliance front for a tighter fit

• One front panel

• Disconnect power (unplug or shut off circuit) before starting any work
• Remove any trim screws, clips, or surrounding panels to access the mounting points
• Handle carefully to avoid scratching the visible finish; align tabs and secure with original fasteners

This felt seal creates a smooth, airtight barrier where the drum meets the bulkhead in your dryer. Replacing a worn seal helps maintain proper airflow, protect fabrics from snagging, and reduce scraping or squealing noises during operation. What it does:

• Seals the gap between the rotating drum and front/rear bulkhead to contain heat and airflow
• Provides a low-friction, cushioned surface for the drum rim
• Helps keep lint and debris out of the cabinet
• Common symptoms of failure: longer or uneven dry times, rubbing/scraping noises, clothes catching or leaving marks at the drum edge, visibly worn or torn felt

• 1 felt seal

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the top/front panel to access the drum and bulkhead; support drum as needed
• Remove old felt and adhesive; clean the mating surface thoroughly
• Dry-fit the new seal; install per manufacturer guidance; allow proper set time before reassembly
• Hand-rotate the drum to verify even contact and clearance, then test operation

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance. 

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching. 

Symptoms of a bad Door Latch include:

• The dryer door doesn't stay closed during cycles.
• Difficulty in starting the dryer due to the door not activating the safety switch.
• Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This drum slide bearing supports the front edge of the dryer drum with a low-friction surface so it turns smoothly. Replacing worn slides can reduce squeaks or scraping and help prevent damage to the drum and front bearing.

• Provides a low-friction contact point for the front of the drum to rotate smoothly
• Reduces rubbing and wear between the drum rim and front bearing assembly
• Worn slides can cause squealing/scraping noises, rough drum rotation, or marks/snags on clothing near the drum opening
• Common maintenance item; uneven or excessive wear may affect tumbling performance

• Disconnect power; for gas dryers, also shut off gas supply
• Access by removing top and front panel per service instructions; support the drum during service
• Replace slides in matching positions/orientation; replacing all slides together helps ensure even support
• Spin the drum by hand before reassembly to ensure smooth, quiet rotation

The Dryer Push-to-Start Switch is an OEM replacement part for GE dryers. This component is responsible for initiating the drying cycle when pressed, serving as the primary control for starting the dryer's operation.

Symptoms of needing to replace the push-to-start switch include:

• The dryer failing to start or begin the cycle when the switch is pressed
• Intermittent or inconsistent starting issues
• Visible damage or deterioration of the switch itself

Causes of a faulty push-to-start switch can include mechanical wear and tear over time, electrical malfunctions, or physical damage due to impact or mishandling.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryer models.

A front bracket that supports and secures the appliance's front panel or control assembly to restore proper alignment and stability. Replaces a worn or damaged bracket to reduce panel movement and rattling. What it does:

• Provides structural support for the front panel or control console so panels stay aligned.
• Secures trim and assemblies to prevent vibration, rattling, or loose panels.
• Restores proper fit and contact points that can affect door or panel operation.
• Helps maintain safe, stable mounting for front-facing components.

• One front bracket.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Confirm correct bracket location and orientation before fastening; use original screws or hardware.
• Do not force parts; if fitment is tight, check for obstructions or bent mounting tabs.

This bearing supports the washer's inner tub shaft so the drum spins smoothly and quietly. Replacing a worn bearing restores proper drum alignment and reduces grinding, wobble, and loud rumbling during spin cycles. What it does

• Supports the inner tub/drum shaft for smooth rotation
• Keeps the drum properly aligned to prevent wobble and vibration
• Reduces grinding, squealing, and other spin-cycle noises caused by worn bearing surfaces
• Helps protect adjacent parts from premature wear by maintaining correct rotation

• One bearing

• Disconnect power and water before beginning repair; drain tub if applicable
• Replacement typically requires partial disassembly of the washer cabinet and removal of the drum/tub
• Use proper tools to avoid damaging the shaft or bearing housing; press-fit bearings often require a bearing puller/press
• Inspect adjacent seals and shaft for wear; replace as needed

This drum slide bearing supports the front rim of the dryer drum so it turns smoothly and quietly. Replacing worn slides restores proper drum support, reducing scraping or squealing noises and helping prevent fabric snags at the door opening.

• Provides a low-friction wear surface for the drum edge inside the front bearing
• Helps keep the drum aligned and rotating smoothly
• Common fix for scraping, squealing, or grinding from the front of the drum
• Replace if the slide is worn thin, broken, or you see plastic/metal dust in the front bearing area

• Disconnect power; for gas dryers, also shut off the gas supply
• Lift the top and remove the front panel to access the front bearing area
• Support the drum, remove the worn slide, and install the new slide in the designated slot on the front bearing
• Inspect remaining slides, the front bearing ring, and felt seals; replace worn components together for even wear

The Lint Trap Assembly is an OEM part for GE dryers. It is responsible for capturing lint and debris from the dryer exhaust, preventing it from clogging the venting system and causing potential fire hazards.

A bad lint trap assembly can be caused by regular use, accumulation of lint, or damage to the trap itself. If the lint trap becomes clogged, torn, or worn out, it can lead to reduced airflow, longer drying times, or even overheating of the dryer.

Symptoms of a bad lint trap assembly include:

• Excessive lint buildup on clothing after drying.
• Longer drying times than usual.
• Overheating of the dryer.
• Visible damage or tears on the lint trap.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This Lint Screen Cover is an original and genuine OEM replacement part for GE dryers. The Lint Screen Cover plays a role in the efficient operation of your dryer. It serves as a protective grid that helps prevent objects from entering the dryer vent and causing potential damage to the internal components.

One common cause is a build-up of lint or debris, which can restrict proper airflow and result in overheating. This can lead to reduced drying efficiency, longer drying times, and potential damage to other components of the dryer.

Here are some symptoms that indicate a faulty Lint Screen Cover:

• Excessive lint accumulation around the dryer vent area
• Restricted airflow and poor drying performance
• Overheating of the dryer
• Unusual noises during operation
• Visible damage or deformation of the grid structure

This genuine GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

This Lint Screen Cover is an original and genuine OEM replacement part for GE dryers. The Lint Screen Cover plays a role in the efficient operation of your dryer. It serves as a protective grid that helps prevent objects from entering the dryer vent and causing potential damage to the internal components.

One common cause is a build-up of lint or debris, which can restrict proper airflow and result in overheating. This can lead to reduced drying efficiency, longer drying times, and potential damage to other components of the dryer.

Here are some symptoms that indicate a faulty Lint Screen Cover:

• Excessive lint accumulation around the dryer vent area
• Restricted airflow and poor drying performance
• Overheating of the dryer
• Unusual noises during operation
• Visible damage or deformation of the grid structure

This genuine GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

The Timer Knob is an OEM part for GE dryers. It is a component that allows users to select and control the drying cycles and settings on their dryer. Designed with durability and ease of use in mind, this knob fits directly onto the timer shaft, providing a reliable interface for setting the dryer's timer. 

Over time, the timer knob can become worn or damaged due to frequent use or accidental impacts. A malfunctioning knob may not engage properly with the timer shaft, making it difficult or impossible to set the dryer cycle. 

Symptoms of a bad Timer Knob include:

• Difficulty in turning the knob or setting the dryer timer
• The knob slipping or failing to engage with the timer shaft
• Cracks or breakage on the knob itself

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This is a replacement knob and clip kit for the control shaft. It restores a secure, easy-to-turn control when the original knob is cracked, loose, or missing, helping you select cycles reliably.

• Turns the control shaft and secures it to the timer or selector
• Helps when the knob is cracked, stripped, wobbly, or falls off
• Can resolve issues selecting or starting cycles due to a loose/missing knob
• Direct-fit replacement designed for compatible models

• Disconnect power before service
• Pull the old knob straight off; remove any remaining clip from the shaft
• Align the new knob and press onto the shaft; install the clip as directed
• Do not force if resistance is high—verify shaft and clip alignment