Parts for Ge DSKS433EB3WW: Backsplash, Cabinet & Front Panel Parts

Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.

Dryer won't start or keeps tripping the breaker? A damaged terminal block disrupts power distribution. DIY repair typically takes 30-45 minutes.

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

Dryer clip cover secures and protects internal components. Replace if broken, loose, or missing to ensure proper part retention and safe operation.

Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.

Dryer won't advance through cycles or stops mid-cycle? This timer and wiring harness kit restores accurate cycle control. Moderate DIY repair.

This is a flexible rubber or felt seal that fits around the perimeter of the dryer door opening. It creates an airtight seal between the door and the drum area to keep heated air inside the dryer during operation. Replace this gasket if you feel hot air escaping around the door, notice longer drying times, or if the seal is torn, flattened, or deteriorated.

Outer decorative trim panel for your dryer control area. Replaces cracked, dented, or discolored panels to restore appearance and protect controls.

Seals the gap between drum and bulkhead in your dryer. Replace when worn to eliminate scraping noises, prevent fabric snags, and maintain airflow.

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance. 

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching. 

Symptoms of a bad Door Latch include:

• The dryer door doesn't stay closed during cycles.
• Difficulty in starting the dryer due to the door not activating the safety switch.
• Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This control component allows selection between four different heat settings and is located on the dryer's control panel. Replace it when heat settings don't change, the switch feels loose or broken, or clothes aren't drying at the selected temperature.

A front bracket that supports and secures the appliance's front panel or control assembly to restore proper alignment and stability. Replaces a worn or damaged bracket to reduce panel movement and rattling. What it does:

• Provides structural support for the front panel or control console so panels stay aligned.
• Secures trim and assemblies to prevent vibration, rattling, or loose panels.
• Restores proper fit and contact points that can affect door or panel operation.
• Helps maintain safe, stable mounting for front-facing components.

• One front bracket.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Confirm correct bracket location and orientation before fastening; use original screws or hardware.
• Do not force parts; if fitment is tight, check for obstructions or bent mounting tabs.

The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.

Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.

Symptoms of bad dryer bearing slides include:

• A loud squeaking or scraping noise during operation
• Difficulty rotating the drum manually
• Clothes taking longer to dry due to improper drum movement
• Visible wear or thinning on the existing slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: metallic. It measures about 13-1/2 inches wide by 3 inches high by 3 inches deep.

Protective cover for your dryer's lint trap that prevents objects from entering the vent. Replace if cracked or broken. Snaps into place. Confirm fit.

Single replacement screw for securing dryer panels and internal components. Replaces lost, stripped, or damaged screws to restore proper fastening.

Protective cover for your dryer's lint trap that prevents objects from entering the vent. Replace if cracked or broken. Snaps into place. Confirm fit.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

Dryer timer knob control for selecting drying cycles. Replace if your original knob is cracked, broken, stripped, or missing from the control panel.

Replace a cracked, broken, or missing dryer control knob. This dial attaches to the control panel and allows you to select cycles and settings.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

This is a plastic selector knob that comes with a retaining clip, used on the washer's control panel to select cycle settings. It attaches to the control shaft and allows you to choose wash cycles and options. Replace this knob if it is cracked, broken, or if the clip has snapped, causing the knob to spin freely or fall off the shaft.

Includes 12 screws. Size: 8-18 ab.