Parts for Whirlpool KSM88PSCMC0: 05 - Base And Pedestal Unit Parts

A replacement mixer beater that restores proper mixing and whipping action for compatible Whirlpool mixers. Replaces a worn, bent or damaged beater so batters and mixtures combine evenly. What it does:

• Spins to agitate and combine ingredients for mixing, beating and whipping
• Restores performance when original beater is bent, cracked or missing
• Helps eliminate uneven mixing and large lumps in batters or dough
• Works as a direct-fit replacement when the beater shaft and lock engage properly

• Unplug the mixer before removing or installing the beater to avoid injury
• Align the beater shaft with the mixer socket and push in until it locks or clicks
• Test on low speed to ensure proper engagement before full use
• If both beaters are worn on a dual-beater model, replace both to maintain balanced mixing

4.5 Quart Polished Stainless Steel Mixing Bowl with Handle for Tilt Head mixers, has enough capacity to mix dough for 6 dozen cookies, 3 loaves of bread or 6 pounds of mashed potatoes in a single batch. Dishwasher-safe for quick and easy cleanup The Stainless Steel Mixing Bowl fits Kitchenaid Stand Mixer models K45SS, KSM75 and KSM95.

This factory fastener secures appliance panels, brackets, and components. Replacing a missing or worn screw restores a tight, rattle-free fit and helps keep parts aligned as designed for reliable operation. What it does:

• Fastens specified components to maintain alignment and structural integrity
• Helps reduce vibration, noise, and loosening from normal use
• Replace if stripped, corroded, or missing
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power and shut off water or gas before servicing
• Match location and orientation; replace one-for-one with the original
• Start threads by hand to avoid cross-threading; use the correct driver bit and do not overtighten
• Inspect related clips/inserts; replace if damaged to ensure proper retention

The Cap-Screw is an OEM component specifically designed for Whirlpool mixers. It contains precision mixing mechanisms that allow users to easily and effectively blend, whip, or beat ingredients.

Symptoms of a bad Cap-Screw include:

• Difficulty turning on or selecting speeds
• Excessive noise or vibration during use
• Inconsistent mixing performance
• Leaks into electrical components

Causes of failure can be faulty power switches, worn gears, damaged housing or bowls, or deterioration of internal wiring over time.

This Cap-Screw is also compatible for use with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and select Kenmore.

The Foot is an OEM part for Whirlpool stand mixers. This component is designed to provide stability and support to the mixer, ensuring it remains steady during operation. Positioned at the base of the mixer, the foot helps to prevent movement and vibration, which can enhance the efficiency of mixing and protect your countertop from scratches.

Symptoms of a failing Foot include:

• The mixer wobbling or moving excessively during use
• Increased noise or vibration when the mixer is running
• Visible wear, cracks, or deformation of the foot pad
• Scratches or damage to the countertop surface beneath the mixer

Causes of a bad foot can include prolonged use that wears down the material, exposure to heat or kitchen chemicals that degrade the foot, or physical damage from moving or storing the mixer.

This OEM Whirlpool part is also compatible with KitchenAid stand mixers.

The K45WW 4.5 & 5 Quart Wire Whip is an OEM part for KitchenAid mixers, specifically designed to fit Whirlpool models. This wire whip is used for incorporating air into ingredients, making it ideal for whipping egg whites, cream, and creating fluffy mixtures for recipes.

You should replace this wire whip if it becomes damaged or worn out. Causes of a bad wire whip can include bending or breaking of the wires due to overuse, exposure to heavy or dense mixtures, or corrosion from prolonged exposure to moisture.

Symptoms of a bad wire whip include:

• Inadequate mixing or whipping
• Bent or broken wires
• Poorly aerated mixtures
• Increased mixing time

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dough hook is the kneading attachment designed to mix and develop dough for breads, rolls and other yeast-based recipes. It restores proper kneading action so dough reaches the right consistency without manual work. What it does:

• Replaces a worn or damaged dough hook to restore mixer kneading performance
• Helps mix and develop gluten for consistent dough texture and rise
• Useful when the original hook is bent, stripped, or no longer engaging the mixer
• Fits into the mixer's drive hub and turns dough efficiently for hands-free kneading

• Disconnect power and remove bowls/attachments before installing
• Slide the hook onto the mixer's drive shaft until it locks
• Test at low speed first to ensure proper seating and operation
• Refer to the mixer's manual for cleaning, care and compatible model information

This latch secures the appliance door and helps ensure a proper close for normal operation. It replaces a worn or broken latch to restore reliable door engagement and user safety. What it does:

• Holds the door closed so the appliance can operate as intended
• Replaces a damaged or broken latch that prevents the door from staying shut
• Helps restore proper alignment and engagement of the door mechanism
• Can reduce door rattling or intermittent closing issues

• Latch

• Disconnect power (and gas, if applicable) before starting any repair
• Remove the door or access panel to reach the latch per your model's service instructions
• Compare the new latch to the old part for correct orientation before installation
• Test the door operation after installation to ensure secure engagement

This latch, link, and lever assembly restores proper latching action so the door or lid closes securely and the appliance can run as intended. It replaces worn or broken linkage that can prevent the latch from engaging.

• Connects the latch to its operating lever to enable smooth open/close action
• Helps resolve issues like a door/lid that won't latch, pops open, or won't start due to an unlatched condition
• Prevents intermittent cycle interruptions caused by a weak or misaligned latch linkage
• Durable components designed to maintain consistent latch engagement

• Unplug or disconnect power before servicing
• Access the latch area per your model's service information
• Note linkage orientation during removal to ensure correct reassembly
• Test latch engagement and operation before returning to service

This pivot screw secures a hinge, lever, or linkage to its bracket to create a stable pivot point. Replacing a missing or stripped screw restores proper alignment and smooth movement of the assembly.

• Fastens a pivoting component to its mounting point
• Maintains alignment and smooth, controlled motion at the pivot
• Helps prevent looseness, wobble, or sag at the joint
• Common symptoms include a missing/loose screw, binding movement, rattling, or uneven gaps

• Disconnect power; shut off gas/water if applicable before servicing
• Support the hinged or moving component to remove load from the pivot
• Remove the damaged screw and start the new screw by hand to avoid cross-threading
• Tighten snugly without over-torquing; replace companion bushings or washers if worn

This wavy spring washer applies light, consistent preload between mating parts so components stay snug and quiet. It helps control end play and vibration, supporting smoother, more reliable operation of the assembly.

• Applies axial spring tension to take up end play between parts on a shaft or fastener
• Helps resist loosening from vibration and keeps components fitting tightly
• Can address wobble, rattling, or uneven spacing when the original washer is worn or missing
• Maintains proper alignment and feel in the assembly

• Disconnect power and shut off gas/water before servicing; allow hot surfaces to cool
• Note the original stack order and position before removal; replace in the same orientation
• Seat the washer evenly and avoid over-compressing during reassembly
• Verify smooth operation and minimal play after installation

This genuine replacement screw secures appliance panels and components to restore proper fit and reduce rattling. Use it when original fasteners are missing, stripped, or broken to reattach parts securely. What it does:

• Fastens panels, brackets or trim to the appliance chassis
• Restores secure fit to eliminate vibration or rattling caused by loose hardware
• Replaces missing or damaged fasteners that prevent proper assembly
• Matches OEM fit and thread for reliable reinstallation

• Unplug the appliance or disconnect power before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten snugly but avoid over-torquing to prevent thread damage
• If threads are damaged, replace with the correct OEM screw rather than reusing

This black control lever knob replaces a cracked, worn, or missing knob, restoring a secure grip and clean, factory look so you can adjust settings comfortably and accurately.

• Attaches to a control lever to provide a comfortable, secure handhold
• Enables smooth, precise selection of settings during use
• Helps keep the lever aligned and easy to operate
• Typical symptoms: knob cracked, stripped, loose, missing, or cosmetically damaged

• Disconnect power before servicing for safety
• Remove the old knob from the lever stem; retain any small hardware if present
• Align the new knob and press or thread it onto the stem until fully seated
• Move the lever through all positions to ensure proper engagement before use

The Hinge Pin is an OEM part for Whirlpool stand mixers. This part allows the tilt head of the stand mixer to pivot smoothly, enabling easy access to the mixing bowl and attachments. The hinge pin ensures that the tilt head remains securely attached while providing stability during operation.

Causes of a bad hinge pin can include general wear and tear, corrosion from exposure to moisture, or damage due to heavy use.  

Symptoms of a bad hinge pin include:

• Difficulty in raising or lowering the tilt head
• Tilt head not locking into place properly
• Unusual wobbling or instability during mixing
• Squeaking or grinding noises when adjusting the tilt head

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Pouring Shield is an OEM part for KitchenAid mixers. This part fits snugly onto the mixing bowl, helping to prevent ingredients from splattering out during mixing. It also features a convenient pour spout that allows for easy addition of ingredients without stopping the mixer.

Causes of a bad pouring shield can include accidental drops or impacts, exposure to high heat, or stress from frequent use.

Symptoms of a bad pouring shield include:

• Difficulty fitting the shield onto the mixing bowl
• Cracks or chips in the plastic
• Ingredients splattering out during mixing
• Difficulty adding ingredients through the pour spout

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

5 Quart Flex Edge Beater For KitchenAid Stand Mixer. The Flex Edge Beater is designed to reduce mixing time when mixing with this beater. The beater features a flexible edge that thoroughly scrapes ingredients from the sides of the bowl and fits KitchenAid Stand Mixer models K45SS, KSM75, KSM95, KSM150PS, KSM152PS and KSM155GB.