Parts for Whirlpool KSM88PSCMC0: 04 - Motor And Control Unit Parts

Secures hinge, lever, or linkage to its bracket on your stand mixer. Replace this screw if stripped, missing, or damaged to restore proper alignment.

Replace your mixer's wavy spring washer to reduce vibration and noise. This washer maintains proper tension between shaft components for smoother operation.

Speed control lever cracked or broken? This mixer speed control lever restores speed adjustment. Simple 15-minute repair with basic tools.

Replacement spring for stand mixer control plate assembly. Maintains tension between speed control lever and plate. Needed when broken, missing, or worn.

Stand mixer bearing supports and centers the rotating drive shaft for smooth, quiet operation. Replace when you hear grinding noises or vibration.

Fixes mixer that won't start, stops under load, or runs weak. This motor armature restores full speed and power when the rotor assembly fails.

This flat washer provides a durable spacer and load-distribution surface for fasteners in laundry appliances, helping secure components and reduce wear. It's a simple replacement that restores proper fastening and alignment where a worn washer is causing issues. This is for 1 washer, the photo is an example of the washer.  

What it does:

• Distributes nut/bolt pressure to protect mounting surfaces and prevent loosening
• Maintains correct spacing and alignment of panels, brackets, or moving parts
• Helps reduce vibration-related noise and abrasion at fastener points
• Common symptom: loose or rattling panels or hardware where a washer has deteriorated

What's included:

• One flat washer

Install notes:

• Turn off power and unplug the appliance before accessing panels or hardware
• Remove the fastener, replace the old washer with the new one, and re-torque to the OEM-recommended specification
• Inspect surrounding hardware and replace any damaged screws or nuts for a secure repair

If your stand mixer runs only on high speed or won't change speeds properly, a worn governor drive stud may be the cause. This small repair restores smooth speed control in about 30 minutes.

Supports moving mechanisms in your stand mixer for smooth operation. Replace if you notice excessive noise, wobbling, or oil leaks. Verify fit with your model.

Seals motor housing to prevent dust and moisture from damaging internal components. Replace if you notice oil leaking or residue buildup. Confirm fit with your mixer model.

If your mixer's attachments or components feel loose or wobbly, this 10-24 lock nut secures threaded fasteners and prevents vibration loosening. Quick fix.

Replace a lost or damaged thermostat mounting screw to secure your mixer's temperature sensor in position for accurate heat control and consistent performance.

Mounting screw for washers and dryers. Secures internal components to the cabinet or frame. Replace if screw is stripped, missing, or broken.

Fix mixer stuck at one speed or won't turn off. This speed link connects to the speed control mechanism. Common DIY repair, takes 30-45 minutes.

Mixer won't turn off or stuck at one speed? This flat spring restores tension to the speed control mechanism. Common fix for speed link issues.

Mixer won't start or stopped working suddenly? A failed field assembly disrupts the motor's electromagnetic field. Moderate DIY repair restores power.

Protects your mixer shaft from wear and metal-on-metal contact. Replace when you notice rubbing noise or rough operation. Verify fit with your model.

Fix a mixer that won't start or runs weakly. Motor brushes wear from normal use and conduct electricity to power the motor. Basic DIY repair.

Mounting screw for washers. Secures internal components and panels. Replace if stripped, rusted, missing, or damaged during repair or maintenance work.

Mixer won't run or just hums? Worn motor brushes in the holder cause power loss. This DIY repair restores full motor function on stand mixers.

Fix intermittent mixer operation or arcing sounds with this brush holder housing. Secures carbon brushes for steady motor contact and consistent speed.

Small fitting that seats inside the brush holder assembly to align and secure the motor brush. Replace if cracked, missing, or worn to restore proper brush positioning.

If your mixer makes excessive noise or vibrates during operation, a worn spring seat cap may be the cause. This part centers and secures springs for smooth, quiet performance.

Fix loose or unresponsive mixer buttons with this cap spring. Restores proper tension and reliable engagement. Simple DIY repair in minutes.

Fix a mixer that won't start or runs intermittently with this brush holder cap. Secures the carbon brush and spring in the motor assembly.

Replacement screw fastener for stand mixers. Secures panels, trim, and brackets to the mixer body. Order when original screws are stripped, missing, or damaged.

Fix a mixer stuck on one speed or operating only at high speed. This speed control plate regulates mixer speed settings. Moderate DIY repair.

Fix a mixer stuck at one speed or losing power under load. This speed governor regulates motor performance. Moderate DIY repair with video guide.

Fix a mixer that won't start, runs constantly, or has only one speed. This phase control board regulates motor speed. Easy DIY repair with video guide.

Replacement power cord for stand mixers. Connects your mixer to the wall outlet. Replace if frayed, heat-damaged, cracked, or loose for safe operation.

Replace your stand mixer's power cord if it's damaged, frayed, melted, or chewed. This electrical cord connects your mixer to the outlet for power.

Fastens panels and internal components in stand mixers. Replace if the original screw is missing, stripped, or damaged to restore secure assembly and fit.