Parts for Kenmore 363.61542211 (36361542211, 363 61542211): Blower & Motor Assembly Parts

Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

Metal bracket that secures the dryer motor and blower assembly in place. Replace if your mounting bracket is cracked, broken, or causing loose components.

Transfers power from motor to drum in your dryer. Replace if squeaking, not spinning, or visibly worn. Confirm fit with your model number before ordering.

Dryer won't heat, overheats, or shuts off mid-cycle? A faulty cycling thermostat often causes these issues. Easy DIY fix with our video guide.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.

This motor and pulley kit replaces a dryer's failed drive motor and pulley assembly to restore drum rotation and normal drying performance. Designed as a direct-fit service kit for compatible GE dryers. What it does:

• Replaces the dryer drive motor and pulley to restore drum tumbling.
• Restores proper belt drive and helps recover normal drying and ventilation.
• Can stop or reduce symptoms like a drum that won't turn, loud grinding, or a dryer that runs but doesn't tumble.
• Designed to work with the dryer's existing belt and mounting hardware when applicable.

• One motor and pulley kit

• Disconnect power to the dryer before starting any repair.
• Basic hand tools are typically required; remove the dryer cabinet or access panel as needed.
• Support the drum while replacing the motor; follow the appliance's service manual for routing the belt and aligning the pulley.

Idler arm assembly mounts to the dryer frame and maintains proper belt tension on the drum. Replace if the arm is cracked, bent, or the pulley is worn.

Exhaust duct channels air from your laundry center to the venting system. Replace if cracked, disconnected, or damaged to restore proper airflow.