Parts for Kenmore 363.61542211 (36361542211, 363 61542211): Cabinet (1) Parts

Size: 8 - 18 ab.

Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.

Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.

Replace a damaged or missing rear panel and fuse cover to restore safe electrical access. Protects wiring and fuse assembly. Simple installation.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

Dryer not heating or shutting off mid-cycle? A faulty safety thermostat can cut heat when temperatures climb too high. Direct heater duct mount part.

Dryer shuts off too soon or won't heat? A faulty high limit thermostat often causes premature shutoff. Simple DIY fix—usually takes 15 minutes or less.

Fix a dryer that won't heat, overheats, or shuts off mid-cycle. This cycling thermostat regulates drum temperature. Easy DIY repair with video guide.

Seals dryer exhaust duct connection to contain airflow and prevent lint entering cabinet. Replace if cracked or loose to restore efficiency. Verify fit.

This replacement drum assembly is the rotating cylinder that tumbles laundry in your dryer. Replacing a damaged or out-of-round drum restores smooth, quiet tumbling and helps protect fabrics from snags, scraping, and uneven drying.

• Forms the rotating chamber that holds clothes; driven by the belt and motor to tumble items for drying
• Works with drum seals and lifters/baffles to maintain airflow and separate fabrics for even drying
• Replacing a dented, cracked, or out-of-round drum can resolve thumping, scraping, or rumbling noises
• Addresses sharp seams, loose spots, or rust that can snag/tear clothing or leave marks

• Disconnect power; shut off gas supply for gas models before service
• Remove top/front panels and release belt tension to lift out the old drum; note belt routing
• Compare parts and move over any reusable, model-specific components if required
• Inspect belt, idler pulley, bearings, and felt seals while open; replace if worn

The Baffle is an OEM part for GE electric dryers. Located inside the dryer drum, it helps separate clothes and improves air circulation during tumbling cycles. 

To achieve consistent drying times, a dryer relies on balanced airflow penetrating all areas where clothes reside. The baffle creates divisions to ensure air fully surrounds each layer instead of bypassing some areas. Its raised ridges also help tumbling action by preventing clumps of clothes.

Symptoms of a bad baffle include:

• Slow, uneven drying requiring extra cycles  
• Certain areas of clothes remain damp while others over-dry
• Reduced airflow output from the vent due to blockage

Replacing it with the genuine GE baffle plate restores optimized air distribution within the drum. The part is also compatible with some Kenmore dryers that use GE elements.

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.

Dryer not heating or taking too long to dry? This heating element and housing assembly restores proper heat generation and airflow for even drying.

Left side panel for washer dryer combo units. Replaces cracked, dented, or discolored exterior panels. Restores cabinet appearance and protects internal components.

Right side panel for washer dryer combo units. Replaces cracked, dented, or damaged exterior panels. Restores cabinet appearance and structure.

Secures front panel on laundry centers. Replace if broken or panel becomes loose. Verify fit with your model number before ordering this clip.

This is the complete door assembly for a dryer, including the outer panel, inner panel, and handle. It seals the dryer drum compartment to contain heat and tumbling clothes during a drying cycle. Replace this assembly if the door is cracked, warped, won't latch properly, or if the window or seal is damaged.

This small mounting screw secures panels and trim on compatible GE appliances, restoring a solid, vibration-free fit. Use it to replace a missing, stripped, or damaged fastener and keep parts aligned and secure. What it does:

• Fastens panels, trim, or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Restores secure attachment when threads are stripped or worn
• Helps maintain proper alignment to prevent noise and component wear

• Use the correct screwdriver size to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power or move the appliance to a safe position when accessing internal panels
• Consider a replacement clip or insert as recommended by the manufacturer

This control knob assembly lets you select cycles and settings on your dryer. Replacing a cracked or stripped knob restores firm engagement with the timer or selector so you can set, start, and adjust drying reliably.

• Attaches to the control shaft to turn the timer or selector
• Provides a secure grip and pointer to choose cycles and options
• Restores proper control when the original knob is cracked or the hub is stripped
• Typical symptoms: knob spins without turning the shaft, feels loose, falls off, or is missing

• Disconnect power to the dryer before servicing
• Pull the old knob straight off; note the shaft shape and orientation
• Align the new knob with the flat/D-shaft and press until fully seated
• If your model uses a separate dial ring or clip, transfer it from the original

Fix a washer dryer combo that won't start or respond to button presses with this start button assembly. Simple repair restores cycle control.

Control panel wire harness for laundry centers. Connects the control board to the front panel. Replace if wires are damaged, frayed, or loose.

Washer won't change cycles or settings not responding? This selector switch routes power to temperature and speed controls. Moderate DIY repair.

Washer won't respond to cycle selections? This selector switch mounts behind the control knob to restore reliable setting changes. Easy DIY fix.

This harness selector is the wire connector assembly that routes power and signals between the selector switch and oven/range control components, restoring reliable connections and control function. What it does:

• Connects the selector/control switch to burners, igniters, or control modules so selections register properly
• Replaces worn or damaged wires and terminals that can cause intermittent control response
• Helps address symptoms like selector positions not responding, intermittent heating, or controls that fail to change settings
• Maintains factory routing and connector fit for a correct electrical connection

• Disconnect power to the appliance before servicing to avoid shock or damage
• Inspect connectors and wire insulation for damage; match connector shapes and pin counts before installing
• Seat all terminal connectors fully and secure any routing clips or retainers

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.