Parts for Ge JAP02SN3SS: 02 - Body Parts

Replacement mounting screw secures panels, brackets, and controls on ranges and ovens. Needed when original screws are missing, stripped, or damaged.

If your range won't heat or power on, a faulty terminal block may be the cause. This connector joins wiring to heating elements. DIY-friendly repair.

Range won't heat or burners stopped working? A burnt or melted terminal block may be the cause. This wiring connection hub routes power to elements. DIY repair in 10-20 minutes.

Single fastening screw for range components. Replaces missing, stripped, or damaged screws that secure panels, brackets, and trim pieces in place.

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Secures the terminal block to your range cabinet. Replace this bracket if damaged, cracked, or missing to properly support the electrical connection assembly.

This speed nut is a clip-on fastener that provides threads for a screw on the appliance. It secures sheet-metal panels, brackets, or trim and helps keep assemblies tight under vibration and repeated use.

• Provides captive threads so a screw can tighten into thin sheet metal
• Helps secure panels, brackets, and trim pieces in place
• Replace if a screw spins without tightening, a panel rattles/feels loose, or the original clip is missing or damaged
• Restores a snug, reliable attachment point without a loose nut

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool before servicing
• Note the clip's orientation; slide it onto the panel edge or stud as designed
• Start the screw by hand to avoid cross-threading; do not overtighten
• Wear cut-resistant gloves when handling sheet-metal parts

Oven door hinge assembly for ranges. Secures and supports the door during opening and closing. Replace if hinge is cracked, bent, or broken.

This housing receptacle is the molded mounting and connection point that secures and protects the oven/range control wiring and plug-in module, helping maintain reliable electrical contact and safe operation of the control components. What it does:

• Provides a secure housing for the control module or wiring receptacle to prevent movement and wear
• Protects electrical connections from abrasion and incidental contact
• Keeps the control harness aligned for consistent plug-in engagement
• Can resolve issues like intermittent control operation or loose control module connections

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Basic hand tools are typically required; note wire harnesses and screw locations before removal.
• Handle plastic tabs and mounting points gently to avoid breakage; replace any damaged fasteners.

Replace your range's light receptacle socket when the oven light flickers or won't turn on. Easy DIY fix restores proper bulb connection. Confirm fit by model.

Anti-tip bracket kit installs to the floor behind your range or wall oven to prevent tipping. Replace if missing, damaged, or moving to a new home.

Original Whirlpool light bulb, 40 watt.

Symptoms of needing to replace the light bulb include:

• Dimming or flickering light
• Complete lack of illumination inside the appliance
• Visible signs of damage or burnout on the bulb itself

Causes of a faulty light bulb can include normal burnout over time, electrical issues, or physical damage due to impact or vibrations.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Kenmore, Frigidaire, GE, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances.

This replacement leveling screw secures and adjusts an appliance's leg so the unit sits level and stable on the floor. Restores proper tilt for even door operation and stable performance. What it does:

• Replaces a worn or damaged leveling screw used to raise or lower an appliance leg
• Helps stop rocking, reduce vibration, and keep doors aligned
• Common fix when an appliance tilts forward/back or is uneven on the floor
• Works with the corresponding leveling leg/assembly to set final height

• Support the appliance before adjusting or removing leveling hardware to prevent tipping
• Use appropriate hand tools; tighten securely but avoid over-torquing
• No electrical disconnection is typically required, but unplug if working near electrical components
• If the leveling leg assembly is damaged, replace the entire leg/assembly per manufacturer instructions

Vent tube for electric ranges and ovens. Connects oven cavity to exhaust system. Replace if cracked, broken, or missing to restore proper ventilation.

Fix oven not reaching set temperature or F2/F3 error codes. This temperature sensor monitors internal heat for accurate cooking. Easy DIY repair.

Clear glass lens that protects your oven light bulb. Replace if cracked, broken, or cloudy to safely view cooking progress. Confirm fit with model number.

Secures range door handles and attaches components. Replace when cracked, bent, or missing to restore stable grip. Confirm fit with your model number.

Wire clip secures electrical connections to heating elements in ranges. Replace if worn, cracked, or loose to restore proper contact. Verify fit with model.

Oven not heating or baking unevenly? This range bake heating element restores proper cooking temperatures. Moderate DIY repair in 30-45 minutes.

This metal bracket provides structural support for range components like burner assemblies or control panels. It securely holds parts in their proper position during normal cooking operations. Replace when range components become loose, sag, or don't align properly.

Replacement drawer support for electric and gas ranges. Holds and guides the storage drawer on its track. Needed when the original is cracked, broken, or worn.

Replacement mounting screw secures panels, brackets, and components in place. Needed when original fasteners are missing, stripped, or damaged.

Range oven not heating evenly or convection fan stopped working? This blower motor circulates air in the oven cavity for even cooking and baking results.

Seals the front frame of your range to prevent heat loss and improve efficiency. Replace if worn, cracked, or causing gaps. Verify fit with your model.

Replacement screw for electric and gas ranges. Secures internal components and panels. Needed when original hardware is stripped, missing, or lost during repairs.