Parts for Kenmore 417.99570800 (41799570800, 417 99570800): Body Parts

Door hinge bar kit for washer dryer combo units. Replaces broken, worn, or damaged hinge bars that prevent proper door alignment and operation.

The hinge grommet provides cushioning and smooth operation where the washer lid connects to the main body. Replace if the lid doesn't close properly, makes grinding noises when opening/closing, or appears loose and wobbly.

Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

This small pin helps align and position the washer's front or top panel during assembly and operation. It ensures proper alignment between panels and maintains structural integrity. Replace this part if panels are misaligned, the washer vibrates excessively, or there are gaps between panels.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replacement pin for washer components. Secures and connects internal parts. Needed when original pin is broken, missing, or worn from use.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.

Shipping block for washers, installs inside cabinet to secure the tub during transport or moving. Replace if lost, broken, or missing from original packaging.

Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Small alignment pin that positions and secures panels or components during assembly. Replace when worn, missing, or damaged to restore proper fit.

White

Right hand

Left hand

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. Instructions included.

This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. Instructions included.

This is a small spring that attaches to the lid of a laundry center washer, providing tension to hold the lid in position. It helps the lid stay open during loading and close securely during operation. Replace this spring if your washer lid won't stay open, slams shut on its own, or the original spring is broken or stretched out.

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

Dryer not heating? This heating element produces hot air to dry clothes. Common DIY repair takes 1-2 hours with basic tools. Fixes no-heat issues.

Ceramic dryer heating element terminal block.

Ceramic dryer heating element housing insulator.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Secures the drain hose to prevent leaks and disconnection during spin cycles. Replace if cracked, loose, or causing water leakage. Verify fit with your model.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

This component adjusts the tension of washer suspension springs in laundry center units and is located within the suspension system. Replace when experiencing excessive vibration, unbalanced loads, or unusual movement during spin cycles.

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.

This part has been discontinued by the manufacturer and is no longer available.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.