Parts for Kenmore 790.97993410 (79097993410, 790 97993410): Body Parts

Replace your range oven door liner if the original is cracked, warped, or discolored. This inner door panel provides insulation and a finished look.

Mounting screw for gas ranges. Secures internal components and panels. Replace if screw is stripped, missing, or damaged during appliance service.

This is a metal broiler pan designed to sit beneath the broil element in the oven or broiler compartment. It catches grease and drippings during broiling to reduce smoke and prevent grease fires. Replace this pan if it is warped, corroded, or has holes that allow grease to leak through.

This broil pan insert fits inside your oven's broiler pan to allow grease and fat to drain away from food while broiling. The slotted design promotes even cooking and prevents food from sitting in grease. Replace this insert if it's warped, has holes burned through it, or is heavily stained and won't clean properly.

This is a door-activated switch that detects whether the oven door is open or closed. It controls functions such as the oven light or signals the control board about door position. Replace this switch if the oven light stays on or off regardless of door position, or if the oven does not operate correctly due to a faulty door signal.

Mounting bracket secures range components to the cabinet or frame. Replace if bracket is bent, cracked, or broken to restore proper alignment and support.

Fix an oven door that won't lock during self-clean or clean cycle errors. This door latch assembly secures the door and reports lock status to the control.

Replace your range oven door seal to maintain heat efficiency and prevent energy loss. Essential when you notice gaps, cracks, or heat escaping. Verify fit.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Oven won't reach or hold set temperature? A faulty temperature sensor causes inaccurate heating. This monitor probe ensures consistent cooking results.

Power cord for electric ranges. Connects your range to the wall outlet. Replace if your cord is frayed, damaged, or missing for safe operation.

Oven displaying probe error or reading temperature when unplugged? This meat probe monitors internal food temperature. Easy DIY replacement part.

Secures burner or oven control to the control panel behind the knob. Replace if stripped, missing, or loose to keep control shaft stable and aligned.

This replacement cabinet insulation helps reduce heat transfer into the refrigerator cavity so cooling components run efficiently and food stays colder. It restores proper thermal barrier and helps control frost and compressor run-time. What it does:

• Replaces worn or damaged foam insulation behind the interior liner
• Restores the refrigerator's thermal barrier to improve cooling consistency
• Helps reduce frost buildup and excessive compressor cycling caused by poor insulation
• Supports sealed-system efficiency by minimizing unwanted heat gain

• Install behind the interior liner or in the cabinet cavity as original; follow OEM location and orientation
• Use proper personal protective equipment when handling insulation (gloves, eye protection)
• Avoid compressing or tearing the foam during installation to maintain thermal performance
• For best results, inspect surrounding seals and fasteners and replace any damaged components

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critical role in the power supply system by providing a reliable connection point for the appliance's main power cord, preventing loose connections and potential electrical hazards.

Symptoms of a bad Terminal Block Kit include:

• Signs of burning or melting at the connection points,
• Flickering power or intermittent operation of the appliance,
• A burning smell from the appliance area.

Causes of terminal block failure often involve loose connections that can lead to arcing and overheating, improper installation, or general wear and tear that degrades the integrity of the electrical contacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This 4,000-watt broil element is mounted at the top of the oven cavity and provides intense direct heat for broiling. It glows red when operating and radiates heat downward onto food placed on the upper rack. Replace this element if the oven does not broil, heats unevenly during broiling, or if the element shows visible damage such as blistering, cracking, or burn-through spots.

Range not heating or baking unevenly? This bake element restores proper oven temperature. Common fix for no heat issues. Moderate DIY repair, 30-45 minutes.

This mounting bracket secures components inside the appliance to restore proper alignment and stability. Replacing a damaged bracket helps stop rattling, sagging, or loose internal parts for quieter, safer operation. What it does:

• Provides a secure anchor point for internal panels or assemblies
• Prevents movement that can cause rattling, misalignment, or wear
• Restores proper fit between components after damage or corrosion
• Helps maintain safe, stable operation of the affected area

• Intended for experienced DIYers;
• Disconnect power and, where applicable, water supply before beginning work
• Use correct fasteners and torque per OEM guidance; do not force or bend the bracket
• Inspect adjacent components and replace any worn hardware to ensure a secure fit

Fix F95 error code or oven door that won't lock during self-clean cycle. This door lock motor assembly repair takes about 15 minutes with basic tools.

This cover mounts over the convection fan assembly inside the oven cavity, shielding the fan blades and motor from direct exposure to food debris and grease. It helps direct heated air circulation for even cooking. Replace it if the cover is warped, rusted, cracked, or if you hear unusual rattling noises coming from behind the oven's rear wall during convection cooking.

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Fix a range cooling fan that won't shut off or makes howling noises with this motor. Requires removing oven from cabinet and back panel access.

Loud grinding or rattling from your oven? A damaged convection fan blade disrupts airflow. This replacement restores quiet operation in 20-30 minutes.

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

Fix noisy convection fan operation with this motor replacement. Restores quiet, even heating in your oven. Moderate DIY repair in 30-60 minutes.

Reinforces and supports oven door glass panels. Replace if original stiffener is bent, cracked, or missing to properly secure glass in the door frame.

This is a 2500-watt circular heating element located at the rear wall of the oven cavity, surrounding the convection fan. It provides even heat distribution during convection baking and roasting by working in conjunction with the fan. Replace this element if your oven is not heating properly in convection mode, food is cooking unevenly, or the element is visibly damaged or broken.

Oven won't heat or shuts off during use? A blown thermal fuse cuts power to prevent overheating. Simple diagnosis with a multimeter, quick replacement.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Replacement mounting screw for range power and control boards. Secures electrical board connections. Needed when original screw is missing or damaged.

Replacement 10-24 x 5/8 screw for securing panels, brackets, and trim on ranges and ovens. Needed when original hardware is stripped, missing, or worn.

Fix intermittent or failed component operation with this wiring harness assembly. Restores reliable electrical connections between range components.

Mounting screw for electric and gas ranges. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

Illuminates your oven interior for visibility while cooking and cleaning. Replace when burned out to restore lighting. Verify fit with your model number.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.