Need Help?
Call or text
Show parts
Replacement control console panel for electric ranges. Restores front trim around controls and display. Replaces cracked, faded, or bent panels.
Usually ships within 4 - 14 days
This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.
Leveling leg assembly installs at the front corners of your range. Replace if broken, rusted, missing, or no longer adjusts to level your appliance.
Color: chrome. Measures about 24 inches wide by 16 inches deep.
This part is discontinued by the manufacturer and is no longer available for purchase.
Replaces the metal panel at the base of your oven interior. Installs on the oven floor. Needed when original is warped, rusted, or damaged by foil.
Oven light stays on or won't turn on when door opens? This door-activated switch restores automatic light control. Easy 15-minute DIY repair.
Fix an oven door that won't lock during self-clean or clean cycle errors. This door latch assembly secures the door and reports lock status to the control.
Secures range trim, panels, and components to prevent rattles and loosening. Replace when clips break or lose tension. Confirm fit with your model number.
Supports smooth drawer movement in your range's storage compartment. Replace when drawer becomes crooked, slides too far, or glide shows wear grooves.
Fix F10 error codes and inconsistent oven temperatures with this sensor probe. Monitors internal temp for accurate cooking. Moderate DIY repair.
Protects internal oven components and directs airflow. Replace if your shield panel is bent, corroded, cracked, or missing to restore proper coverage.
Shield protects the wire harness near the vent tube in your range. Replace if cracked, damaged, or missing to prevent wire exposure and ensure safe operation.
Molded insulation liner that fits inside the range oven cavity. Replace if yours is damaged, compressed, or missing to restore proper heat containment.
Insulation panel for range oven cabinet that reduces heat transfer and noise. Installs on top and sides. Replace if worn, damaged, or missing.
Insulation blanket surrounds the oven cavity to retain heat. Replace if burnt, deteriorated, or damaged by pests to restore proper heat retention.
Upper oven vent tube for gas and electric ranges. Channels hot air from the oven cavity to the exterior vent. Replace if cracked, damaged, or missing.
Ceramic catalyst insert for range oven vents. Breaks down cooking odors and residues at high temperatures. Replace if cracked, clogged, or missing.
The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critica
Stop rattling and loose panels in your range with this support plate. Secures internal components, reduces vibration, and restores proper alignment.
Oven won't broil or heats unevenly? The broil element provides high heat from above for browning. DIY-friendly repair, usually takes 10 minutes to replace.
Oven won't heat or bake properly? This bottom bake element converts electricity to heat for even baking. Simple DIY fix—2 screws, 2 wire terminals.
Right-side oven rack support mounts to the interior wall to hold and guide oven racks at proper heights. Replace if cracked, broken, or missing.
Replace your range's heat shield if it's cracked, warped, or missing. This protective barrier installs between heating elements and components.
This electrical receptacle is the small connector that secures a wiring plug to an appliance component, restoring a reliable electrical connection and preventing intermittent operation or arcing. What it does:
Mounting plate for electric and gas ranges. Secures components in place. Replace if cracked, bent, or broken to restore proper structural support.
Replacement door latch rod for electric and gas ranges. Installs in the door mechanism to secure the latch assembly. Order a new rod if broken or missing.
Fix F95 error code or oven door that won't lock during self-clean cycle. This door lock motor assembly repair takes about 15 minutes with basic tools.
Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.
Push-in plug button that covers openings in the oven bottom panel. Replace if cracked, missing, or broken to keep debris out and maintain a clean finish.
Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.
This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does
Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.
Size: 6-20 x 0.312 inch.
Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.
Size: 8-32t x 0.500 inch. Color: Black.
Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.
The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.
The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or o