Bosch Washer Parts

Drum shock absorber for front-load washers. This damper connects the tub to the chassis and controls movement during wash and spin, reducing vibration and noise so the washer can ramp to proper spin speed without banging.

• Damps and stabilizes the drum to control vibration during acceleration, spin, and coast-down
• Helps reduce shaking, banging, and "walking" across the floor
• Can help address out-of-balance messages and noisy operation
• Worn shocks may leave loads wet after spin or cause loud thumping

• Disconnect power and shut off water before servicing; move the appliance to access panels safely
• Access the shock from the front or rear per model; support the tub to relieve tension
• Note pin/bolt orientation; transfer any reusable hardware and fully seat both ends of the new shock
• Consider replacing them as a set for balanced damping; run a short test cycle to verify stability

Replacement oven door handle that restores a secure grip for opening and closing the oven door. Replaces cracked, broken or loose handles to help make daily use safer and more reliable. What it does:

• Provides a firm grip to open and close the oven door smoothly.
• Replaces handles that are cracked, broken, loose, or missing.
• Helps prevent further damage to door trim and reduces the risk of sudden handle failure.
• Designed for factory mounting locations for a straightforward swap.

• Disconnect power to the appliance before starting; for gas units, turn off the gas supply if applicable.
• Support the door while removing and installing the handle to prevent the door from dropping — use a helper if needed.
• Remove existing mounting screws or fasteners, position the replacement handle, then reinstall and snug hardware.

This washing machine shock absorber stabilizes the outer tub during wash and spin. Replacing a weakened damper helps control vibration and noise so the washer runs smoother and is less likely to shake, bang, or walk.

• Mounts between the tub assembly and cabinet/base to cushion movement
• Helps prevent excessive vibration, shaking, and thumping noises
• Can reduce "walking" or out-of-balance interruptions when a damper is worn
• Supports smoother, quieter spin performance

• Disconnect power and turn off water supply before servicing
• Remove the appropriate access panel(s) to reach the dampers
• Support the tub when removing mounting pins/bolts; match the original orientation
• Inspect all dampers; replace any that show wear for balanced performance

Door handle pin secures the appliance door handle to the door assembly, restoring a firm, stable grip and preventing the handle from slipping or detaching. What it does:

• Acts as the pivot/fastening pin that holds the door handle to the door or door trim.
• Replaces worn, bent, or broken pins that cause loose, wobbly, or sagging handles.
• Helps prevent the handle from falling off or catching when opening and closing the door.
• Restores proper alignment and reliable leverage for normal door operation.

• Disconnect power to the appliance before starting any work; for water-connected appliances also turn off water supply.
• Remove the handle and any trim carefully to access the pin; keep small fasteners in a safe place.
• Install the pin in the same orientation as the original; if retaining clips or bushings were present, reuse or replace them as needed.
• If you encounter springs, clips, or hidden fasteners, proceed cautiously.

This front drum motor mounting bushing supports the dryer drum shaft and helps the drum spin smoothly for quiet, even drying. It replaces a worn bearing surface to reduce noise and prevent drum misalignment. What it does:

• Provides a low-friction bearing surface for the drum shaft at the front motor mount
• Helps keep the drum properly aligned during rotation
• Reduces squealing, grinding, or rubbing noises caused by a worn front bushing
• Prevents excess wear on the drum shaft and adjacent components when functioning correctly

• One front drum motor mounting bushing

• Disconnect power before beginning any repair and follow all safety precautions
• Inspect the drum shaft, drum seal, and rear bushing for wear and replace as needed
• Use appropriate tools to remove the old bushing and press or seat the new bushing evenly
• Re-check installation and related components if alignment or noise persists after replacement

Includes(1)Shipping Bolt,(1)washer,(1)sleeve

The Shipping Bolt is an OEM part for Bosch washing machines. This bolt is designed to secure the washer drum assembly during shipping to prevent excessive movement and potential damage.

Causes of a bad shipping bolt can include stripping, damage to the threads, or loss of the bolt entirely during shipment or installation.

Symptoms of a damaged or missing shipping bolt include:

• Excessive shaking or rattling noises from inside the washer drum
• The drum not rotating properly during wash cycles
• Reduced washing efficiency and improper washing performance

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This heating element replaces the dishwasher tub heater to warm wash water and support drying performance. Restores proper water temperature so detergents and rinse agents work effectively during cycles. What it does:

• Heats wash and rinse water to help remove soils and dissolve detergent
• Supports the dry cycle by raising tub temperature for improved moisture removal
• Helps maintain correct cycle temperatures for sanitation and cleaning performance
• A failed element can cause no-heat conditions, poor drying, or extended cycle times

• Disconnect power to the appliance before starting any work to avoid electric shock
• Inspect and replace only the element shown in the service diagram; handle with care to avoid damage
• Verify electrical connections and test the element for continuity with a multimeter before and after installation

2 included - Front load

This holder is a replacement mounting bracket that secures a small internal component in place to restore proper alignment and support. It helps keep parts stable so the appliance operates as intended. What it does

• Secures and supports an internal component to prevent movement or misalignment
• Replaces cracked, broken, or worn mounting points that allow rattling or improper part position
• Restores stable contact where a loose component causes intermittent operation or noise
• Fits a specific OEM location; use the part number to confirm exact application

• One replacement holder/mounting bracket

• Disconnect power and water before starting any repairs
• Inspect surrounding clips or fasteners and reuse or replace as needed—this part typically snaps or screws into place
• Handle plastic mounting parts gently to avoid cracking during installation

A flat seal ring that forms a watertight gasket for pumps and valves, helping prevent leaks and maintain proper water flow in appliance wet systems. Replaces worn or damaged rings to restore reliable sealing. What it does:

• Creates a tight seal between mating metal/plastic parts to stop water leaks
• Keeps pump housings and valve connections watertight under normal operating pressure
• Helps maintain correct water flow by preventing bypass around seals
• Commonly replaced when brittle, cracked, or deformed from wear or heat exposure

• Disconnect power and shut off water supply before starting any repair
• Inspect mating surfaces for damage or debris and clean before installing new ring
• Seat the ring evenly without twisting or over-stretching to avoid leaks