Bosch Washer Parts

Rear drum seal for washers prevents water leaks from the tub. Replace if you notice leaking during cycles or dampness behind the drum. Verify fit with your model number.

This inner oven door window provides the clear, heat-resistant viewing panel that lets you monitor cooking without opening the door. Replacing damaged or cloudy glass restores safe visibility and helps maintain oven temperature. What it does:

• Serves as the interior viewing glass for the oven door
• Keeps heat contained while allowing you to see inside the oven cavity
• Commonly replaced for cracks, chips, fogging, or shattered glass
• Helps reduce heat loss from a damaged or broken door panel

• One inner oven door window

• Disconnect power to the appliance before starting any repair
• Allow the oven and door to cool completely; wear cut-resistant gloves and eye protection when handling glass
• Removal may require partially disassembling the oven door and carefully detaching retaining clips or screws

Spanner wrench tool designed for washer repairs and maintenance. Essential for tightening or loosening retaining nuts during installation or service work.

Fix a washer that won't drain or shows error codes E03/E04. This drain pump removes water after each cycle. Moderate DIY repair with basic tools.

Plastic bushing that sits between the washer door hinge and pivot point. Replace when worn, cracked, or causing loose door alignment and noisy operation.

Seals the connection between your washer's supply hose and inlet fitting. Replace when flattened or damaged to stop drips and restore a watertight seal.

Fix water leaking into your washer when off or during cycles. This dual inlet valve controls hot and cold water flow. Accessible from the top panel.

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that cause drum sagging or instability during operation.

This dishwasher sump assembly houses the pump inlet and integrated ball check valve to route wash water to the drain while preventing backflow. Replaces worn or cracked sumps to restore proper draining and prevent leaks. What it does

• Collects and channels dishwasher wash water from the tub to the drain pump.
• Integrated ball check valve stops backflow into the sump, helping prevent standing water and odor.
• Restores proper drain function when the existing sump is cracked, clogged, or leaking.
• Compatible with common Bosch/BSH dishwasher pump systems that use a molded sump with ball valve.

• One sump with integrated ball check valve (single assembly only).

• Disconnect power and water supply before starting any repair.
• Access typically requires removing the dishwasher lower kickplate and possibly tilting the unit; support the unit and follow the OEM service manual.
• Inspect surrounding seals, hoses, and pump gaskets for wear and replace as needed.

Fix a washer that won't stop filling or overfills during cycles. This water level pressure switch senses and regulates fill levels to restore proper operation.

Secures rotating components in your washer to prevent movement and vibration. Replace if parts feel loose or noisy. Confirm fit with your model number.

Drain hose adapter for washers. Connects the drain hose to your plumbing system. Replace if cracked, broken, or leaking to ensure proper drainage.

Replacement suspension spring for your washer drum assembly. Installs to support the tub and absorb vibration. Order a new spring if yours is broken or stretched.