Parts for Electrolux EIMGD55IMB4: 11 - Burner Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Mounting bracket secures internal dryer components to the chassis. Replace if broken, bent, or missing to restore proper alignment and stop rattling.

Replacement screw for securing dryer trim, panels, and interior components. Needed when original fastener is lost, stripped, or damaged during repair.

Dryer won't heat or shows E66 error? The thermal limiter prevents overheating by monitoring airflow. Moderate DIY repair, requires rear panel access.

The Thermostat is an OEM replacement part for Frigidaire dryers. It plays a crucial role in monitoring and regulating the temperature inside the tumbler. The thermostat works closely with the heating element and controls to accurately sense temperature fluctuations and modulate heating levels accordingly.

Symptoms of a bad thermostat include:

• Clothes taking an overly long time to dry
• The dryer is heating excessively and tripping the breaker
• Temperature display or heater lights not functioning
• Clothes drying unevenly, still damp in spots

Causes can be normal wear over extreme heating and cooling cycles. Environmental contaminants may also impact sensor performance.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Wire harness connects electrical components in your dryer. Replace if wires are frayed, corroded, melted, or damaged to restore safe power routing.

Replacement pipe cap for dryers. Covers and seals pipe openings in your dryer's internal system. Order a new cap if yours is cracked, broken, or missing.

Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.

Dryer won't heat or stops heating after 10-15 minutes? Gas valve coils control burner ignition. Simple 5-10 minute repair with video guide included.

Dryer won't heat or stops heating after 10-15 minutes? Gas valve coils control burner ignition. Simple 5-10 minute repair with video guide included.

Burner orifice that meters gas flow to your dryer's burner. Replace if clogged, damaged, or wrong size for fuel type during LP/natural gas conversion.

Dryer not heating? A failed igniter won't light the gas burner. This glow-bar igniter heats up to ignite gas during each cycle. Moderate DIY repair.

Replacement mounting collar secures and aligns dryer components for proper fit. Replace when worn or damaged to restore original spacing and support.

Dryer won't heat? A faulty gas burner assembly prevents proper flame and ignition. This part restores heat for efficient drying. DIY repair in 1-2 hours.

Electrical wiring harness that routes power between dryer components. Replaces damaged, frayed, or corroded harnesses with broken connectors or melted wires.

Dryer not heating or flame goes out after igniting? This flame sensor monitors burner temperature to regulate gas flow. Easy 15-minute DIY repair.

This replacement tube routes defrost melt and condensation away from the freezer compartment to the drain pan, helping prevent leaks and ice buildup. Fits specific Frigidaire refrigerator models—check product fit for compatibility. What it does:

• Channels defrost water from the evaporator area to the drain system to prevent pooling
• Helps stop ice accumulation that can block drains and reduce cooling efficiency
• Restores proper water flow when original tube is cracked, split, or clogged
• Compatible direct-replacement when matched to the appliance model/PN

• Disconnect power before starting any repair to avoid electrical shock
• Use appropriate clamps or retainers from the appliance as originally installed; replace damaged clips if needed