Parts for Kenmore 791.7858890 (7917858890, 791 7858890): Burners Parts

This ferrule is a small compression fitting used to secure and seal a refrigerator water line connection, helping stop leaks and maintain proper flow to the ice maker or dispenser. It's a simple replacement to restore a tight water connection. What it does:

• Secures tubing to a compression or shutoff fitting to prevent leaks at the connection
• Restores a proper seal for water supply lines feeding the ice maker or dispenser
• Commonly used when a loose, dripping, or leaking water line is present
• Helps prevent water damage from failing or corroded fittings

• One ferrule

• Turn off the water supply and relieve line pressure before servicing
• Confirm tubing is cut square, fully inserted, and the ferrule is seated before tightening
• Tighten fittings per manufacturer guidance; avoid over-tightening which can damage tubing
• After installation, turn water back on and check carefully for leaks

Gas burner won't light or clicks but doesn't ignite? Replace the igniter switch to restore spark and reliable lighting. Simple 15-30 minute DIY fix.

Oven won't heat, slow to reach temperature, or glows dull orange? This igniter fixes weak ignition. Moderate DIY repair with basic hand tools.

Oven won't light or ignites with a loud pop? A faulty igniter is usually the cause. Simple DIY fix—disconnect two screws and wire nuts to replace.

By Frigidaire. 2+0 module type. Employs two spark electrodes for manual surface ignition of a four burner range top with flash tubes to front and rear burners. Very popular module used on many different brands and models. Check by appliance model number, if not sure.

This part has been discontinued by the manufacturer and is no longer available.

Oven won't light even though igniter glows? Burner lights only when valve is tapped? Replace the dual gas safety valve. DIY install in under 1 hour.

Mounting bracket that secures the gas pressure regulator to your range frame. Replace if bent, broken, or missing to properly support the regulator assembly.

The pressure regulator with bracket controls gas flow to the range burners and is typically located behind the range. Replace when burners won't light, flame is irregular, or you smell gas during operation.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Protective wire shield for gas range safety valve. Replaces cracked, damaged, or missing guards. Installs over valve wiring for safety and protection.

Secures the clock assembly to the control panel on your oven. Replace if clips are broken or missing to properly mount the clock. Verify fit with model number.

A small replacement screw used to secure an appliance handle. Installs quickly to restore a loose or missing handle-fastening point so doors and drawers close and open securely. What it does

• Secures the handle to the appliance door or drawer
• Restores firm attachment when the handle is loose or rattling
• Prevents the handle from coming off during normal use
• Works as the OEM-style fastener for compatible Frigidaire handles

• Turn off and unplug the appliance or disconnect power before starting any repair
• Use the correct screwdriver bit and size to avoid stripping the screw head
• Thread the screw in straight and tighten until snug; avoid over-tightening
• Keep small parts away from children and dispose of any damaged fasteners

Range door latch shield that covers and protects the top latch mechanism. Replace if cracked, broken, or missing to restore proper door alignment.

Rubber bumper that cushions the range door or drawer when closing. Replace if cracked, worn, or missing to prevent rattling and protect surfaces.

This adhesive identification label replaces a torn, faded or missing appliance sticker so model, serial or safety information is legible again. It helps you confirm appliance details for service, parts or safety checks. What it does:

• Restores readable model/serial and specification information that is printed on the original sticker
• Replaces damaged or faded identification and safety labels
• Makes it easier to verify the correct part or service information before repair
• Helps meet safety and inspection needs by restoring visible manufacturer info

• One adhesive identification label

• Clean and dry the mounting area before applying to ensure good adhesion
• Peel backing and press label firmly; hold for several seconds to set
• Avoid placing on textured or insulated foam surfaces where adhesion may be poor

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Cable retainer for cooktop installation. Secures wiring harnesses in place. Replace if broken, cracked, or missing to properly organize internal cables.

Sound dampening insulation for gas ranges. Installs inside the range cavity to reduce noise and provide thermal protection. Replace if worn, torn, or missing.