Parts for Ge GTUP240EM2WW: 11 - Cabinet (4) Parts

Size: 8 - 18 ab.

Mounting screw for laundry center units. Secures panels and components inside the cabinet. Replace if stripped, missing, or damaged during repairs.

Replacement hex washer head screw for laundry center panels and components. Needed when original fasteners are stripped, missing, or damaged during repair.

Secures components inside your washer to prevent movement, loose connections, and rattling noise. Replace when worn or missing to restore stability.

Replacement alignment pin for laundry center hinge or latch assemblies. Restores proper positioning of moving parts when original is broken, worn, or missing.

Replace the top cover panel on your washer dryer combo unit. This protective panel covers the upper cabinet area and may need replacement if cracked or damaged.

Fix bleach pooling or uneven dispensing in your laundry center. This funnel directs bleach into the wash tub, preventing spills and odor issues.

Rubber washer that cushions and seals the lid on laundry center units. Replace if worn, cracked, or missing to ensure proper lid closure and alignment.

This lid actuator engages the washer's lid switch or lock when the lid closes, signaling the control that it's safe to run. Replacing a worn or broken actuator restores reliable lid detection for wash and spin cycles.

• Engages the lid switch/lock when the lid is closed
• Signals the control to allow the washer to start and spin
• A damaged or missing actuator can lead to "lid open" errors
• Common symptoms include won't start, won't spin, or lid lock light flashing

• Disconnect power before servicing
• Access the lid switch/lock area; remove the failed actuator
• Install the new actuator, aligning it to the original mounting points; reuse existing hardware
• Close up and test lid detection before running a full cycle

Front panel assembly for laundry center units. Replaces cracked, damaged, or discolored exterior panels. Restores the cabinet's appearance.

Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.

Retaining clamp secures hoses and tubes to prevent leaks and loose connections in your washer dryer combo. Replace if worn or damaged. Verify fit with model.

Secures the drain boot or hose to the washer tub outlet to prevent leaks and separation. Replace if leaking or hose detaches. Confirm fit with model.

Small drain fitting that routes overflow water away from your laundry center. Replace if cracked, broken, or leaking to prevent water damage and spills.

Seals the top of the outer tub to contain water and suds. Replace if cracked, broken, or worn to restore proper sealing and protect garments during wash.

Internal drain hose routes wastewater through the washer drain path. Replace if cracked, kinked, or leaking to prevent water damage to floors and components.

Secures wiring and hoses in your laundry center to prevent rubbing and wear. Replace when broken or missing to maintain proper routing. Verify fit.

Fix a washer that won't drain or leaves standing water. This drain pump removes water from the drum during drain and spin cycles. Moderate DIY repair.

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit

Secures the capacitor in your laundry center. Replace if clip is broken, cracked, or capacitor becomes loose. Verify fit with your model number.

Rear drum support rod assembly for washer dryer combos. Mounts at the back of the drum to maintain alignment and stability. Replace if bent, worn, or compressed.

Front suspension rod assembly that supports and stabilizes the washer tub from the cabinet. Replace if worn, broken, or causing excessive vibration.

Plastic cup that holds the suspension rod at the tub connection point. Replace if cracked, worn, or broken to restore proper tub support and alignment.

Protective cover for the main wiring harness on laundry centers and washer-dryer combos. Replaces cracked, broken, or missing covers that expose wiring.

Main wire harness for washer dryer combos. Connects electrical components throughout the unit. Replace if wires are frayed, damaged, or connections are loose.