Parts for Frigidaire DE2000D-W1: 02 - Cabinet And Component Parts

The Dryer Drum Bearing is an OEM part for Frigidaire dryers. It supports the dryer drum, ensuring smooth rotation during the drying cycle. This part attaches to the inside of the rear panel of the cabinet, offering support to the dryer drum. 

You should replace the drum bearing if it becomes worn out or damaged. Causes of a bad drum bearing can include normal wear and tear, overloading the dryer, or lack of lubrication.

Symptoms of a bad drum bearing include:

• Loud squeaking or grinding noises during operation
• The drum not turning smoothly or becoming misaligned
• Increased friction causing overheating or burning smells
• The dryer not tumbling clothes properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

For a complete drum bearing and shaft kit order 5303281153.

A single replacement screw fastener used to secure trim, panels, or internal components. Fits specific Frigidaire appliance locations to restore proper fastening and alignment where factory hardware is missing or damaged. What it does:

• Secures plastic trim, brackets, or metal panels in refrigerators and freezers
• Restores proper alignment and prevents rattling or loose parts
• Replaces stripped, corroded, or lost hardware to maintain appliance function
• Works wherever the original factory screw was specified

• One replacement screw

• Use the correct screwdriver or bit to avoid damaging the screw head
• Do not overtighten; snug until seated to prevent cracking plastic or stripping threads
• Replace only with the exact factory part for proper fit and function
• Unplug the appliance or turn off power first if working near electrical components

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

The Dryer Belt (Flat Style) is an OEM part for Frigidaire dryers. It wraps around the drum, motor pulley, and idler pulley, enabling the drum to spin when the motor is running.  

Causes of a bad dryer belt can include wear and tear from regular use, overloading the dryer, or damage from items getting caught in the drum.  

Symptoms of a bad dryer belt include:

• The dryer drum not spinning
• The dryer making unusual noises
• The motor running but the drum remaining stationary
• Clothes taking longer to dry or not drying at all

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Sold individually.

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum. 

Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.

Symptoms of a bad seal include: 

• Increased drying time as heat escapes 
• Excess lint and moisture accumulation inside dryer components
• Visibly worn or cracked seal edges
• Cool air leakage noticed around the door when the dryer is running

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This small retainer clip secures trim, panels, or components in place to prevent rattling and keep parts aligned. It's a simple replacement that restores proper fit and reduces vibration or loose panels. What it does:

• Holds appliance trim or panel pieces in position to prevent movement and noise
• Helps keep wiring or small components routed and secured away from moving parts
• Stops gaps or misalignment that can cause rubbing or vibration sounds
• Restores the intended fit where a worn or broken clip allows play

• Disconnect power to the appliance before starting any repair
• Access the clip location by removing the applicable trim or panel per your model's service instructions
• Use common hand tools; replace broken clips with the identical style to ensure proper fit
• Replace all matching clips for consistent fit

For a complete drum bearing and shaft kit order 5303281153.

The Ball is an OEM part for Frigidaire dryers. This part helps the drum to rotate smoothly and evenly. It provides a stable and low-friction contact point, allowing the drum to turn efficiently during drying cycles. This is a drum-bearing ball only. For a complete drum bearing and shaft kit order 5303281153.

Causes of a bad ball can include regular wear and tear, friction from continuous drum rotation, or physical damage. 

Symptoms of a bad dryer ball include:

• Squeaking or grinding noises during operation
• The drum not rotating smoothly or becoming unbalanced
• Increased friction leading to higher energy consumption
• Visible wear or damage to the ball

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This timer shield is a molded cover that protects the appliance's timer/control mechanism from dust, debris and accidental contact, helping the timer operate reliably and extending component life. What it does:

• Covers the timer assembly to shield electrical contacts and the timer shaft from contaminants
• Reduces risk of shorting from debris or accidental contact with the timer
• Helps prevent intermittent timer operation caused by dirt or physical interference
• Appropriate for repairs where the original timer cover is cracked, missing, or damaged

• Disconnect power to the appliance before beginning any service
• Remove any control knobs or bezel needed to access the timer, then snap or screw the shield into place per the original orientation
• Inspect surrounding components (timer mounting, wiring) while the control is exposed; replace damaged parts as needed