Parts for Frigidaire FFHT2033VS2: Cabinet Parts

Replaces a cracked, broken, or missing refrigerator housing cover assembly. Encloses internal components and wiring while restoring a clean appearance.

Fixes refrigerator running constantly, freezing food, or not cooling properly. This temperature control assembly monitors cabinet temp and cycles cooling.

Refrigerator not cooling but freezer works? Broken evaporator fan blade stops cold air circulation. Easy DIY fix in under an hour with basic tools.

Securing ring holds components in position within your refrigerator assembly. Replace if worn, damaged, or missing to restore proper fit and alignment.

Seals openings where tubes or wires pass through your refrigerator cabinet. Replace if cracked, torn, or causing air leaks. Confirm fit with your model.

If your refrigerator fan rattles or vibrates loudly, this evaporator fan motor grommet cushions the motor mount and stops the noise. Quick DIY fix.

Mounting bracket that secures the shroud or cover to your refrigerator cabinet. Replace this bracket if cracked, bent, or broken to restore alignment.

Internal compartment cover for refrigerators. Shields and supports components inside the unit. Replace if cracked, broken, or missing to restore protection.

Refrigerator not cooling but freezer works? A failed evaporator fan motor stops cold air circulation. This DIY repair takes 10-15 minutes with basic tools.

Refrigerator interior light won't turn on or stays on? This door light switch controls your fridge lighting. Quick DIY fix with basic tools.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Black button plug that covers upper hinge mounting holes on your refrigerator. Replace if original plug is missing, cracked, or broken for a clean finish.

White plastic button plug that covers unused hinge holes on refrigerator doors. Replace if cracked, missing, or discolored for a clean finished look.

Lower hinge bracket secures the refrigerator door at the bottom, allowing smooth pivoting. Replace if bent, cracked, or causing door misalignment and sagging.

Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.

Fits between the refrigerator door and hinge pin to set door height and reduce friction. Replace if worn, missing, or damaged for smooth door movement.

Center hinge bracket mounts between refrigerator doors at the middle hinge location. Replace if cracked, broken, or missing to secure door alignment.

Black center hinge bracket mounts between refrigerator doors to support and align them. Replace if bent, cracked, or worn to restore proper door swing.

Sits on the center hinge pin to maintain proper door spacing and smooth pivoting. Replace if worn, cracked, or missing to restore even door alignment.

Supports and pivots the refrigerator door at the center hinge bracket. Replace if worn, damaged, or missing to restore smooth door swing and alignment.

Secures the top of your refrigerator door to the cabinet. Replace if cracked, broken, bent, or lost during a move to restore proper door alignment.

Black upper hinge cover conceals and protects your refrigerator's door hinge assembly. Replace if cracked, broken, or missing to restore appearance.

White plastic cover that snaps onto the upper door hinge. Replace if cracked, broken, or missing to restore a finished look to your refrigerator.

Replacement shelf support grommet for refrigerators and freezers. Provides stability for shelves. Replace if broken, missing, or worn to restore proper shelf support.

Specs: Hex head ,1/4-20 x 5/8

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

Replacement lower hinge pin for refrigerator doors. Acts as a pivot point to hang and support the door. Replace if worn, broken, or missing from a move.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Replace missing or stripped #10-32 x 3/4" screws that secure panels, brackets, and trim on refrigerators. Restores tight fit and eliminates rattles.

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

Kickplate grille that covers the bottom front of your refrigerator. Replace if cracked, broken, or missing clips cause it to fall off repeatedly.

Decorative panel at the base of your refrigerator that provides ventilation access. Replace if cracked, broken, or missing. Snaps into place easily.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports refrigerator crisper or bin drawers for smooth gliding. Replace when drawers stick or bind. Confirm fit with your model number listed.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Plastic plug insert for refrigerator panels and structural openings. Replace if cracked, broken, or missing to maintain proper cabinet appearance.

Seals the evaporator coil cover to prevent air bypass and direct cold air over coils. Replace if worn or damaged to restore airflow and reduce frost.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Replacement front roller assembly for refrigerators. Includes leveling screw. Needed when roller is cracked, broken, or leveling screw is bent or damaged.

The Harness is an OEM part for Frigidaire refrigerators. It plays an important role in connecting various control boards and electrical components within the refrigerator. The harness routes power and sends signals between things like the control panel, dispenser control board, ice maker, temperature sensors, and more. Proper routing and connections are needed for the refrigerator's electronic systems to operate as intended. 

Causes of a bad harness can include damage from wear and tear over time, improper installation or routing during maintenance/repair work, and exposure to excess moisture or impact within the appliance cabinet. 

Symptoms of a bad harness include:

• Lights or other components not working properly
• Error codes appearing on the control panel  
• Improper cooling or temperature control
• Noisy or intermittent compressor operation
• The ice maker or dispenser malfunctioning

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 
 

Color: White

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.