Parts for Frigidaire PRFC2383AF1: Cabinet Parts

This replacement door gasket seals the freezer compartment to help keep cold air in and warm air out, improving temperature stability and energy efficiency. It restores a tight seal for effective cooling and frost control. What it does:

• Creates an airtight seal around the freezer door to prevent cold air loss
• Helps reduce frost buildup and maintain consistent internal temperatures
• Can improve cooling performance and reduce run time from air leaks
• Common symptoms: visible gaps, torn or deformed gasket, frost buildup, or higher-than-normal appliance run time

• Remove the old gasket and clean mounting surface of dirt and old adhesive before installing
• Start at one corner, align the gasket, and press into the door channel evenly for a full seal
• Some gaskets seat better after a short warm water soak or gentle stretching—follow OEM guidance
• If magnets or mounting clips are present, confirm they are engaged.

This replacement door gasket seals the refrigerator compartment to keep cold air in and warm air out, helping maintain consistent temperatures and reduce energy use. It fits along the cabinet opening and forms the primary seal between door and cabinet. What it does:

• Creates an airtight seal to help maintain internal cooling and reduce compressor runtime
• Prevents warm, moist air from entering and causing frost build-up or condensation
• Helps keep food fresher by maintaining stable temperatures
• Common symptom: visible cracks, gaps, or torn edges around the door perimeter
• Common symptom: warm spots inside the fridge, excessive frost, or higher energy use

• Unplug or disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the sealing surface thoroughly before installing the new gasket
• Some installations require basic hand tools; check the appliance's service guide for detailed steps
• If adhesive or clips are used, follow OEM instructions

Nylon

The Motor Mount Bushing is an essential OEM component inside Frigidaire bottom-mount refrigerators. It secures the evaporator fan motor securely while cushioning vibrations transmitted to the refrigerator body.  

Causes of failure include natural wear of plastic glide surfaces from prolonged absorption of mechanical stresses during compressor and fan operation cycles. Deformations compromise uniform motor positioning over time.

Symptoms of a worn motor mount bushing include:

• Rattling noises emanating from the refrigerator fan area
• Reduced air circulation leading to warmer interior temperatures 
• Lubricant leaks at the mounting point requiring replacement

This authentic OEM replacement is compatible with Frigidaire, Electrolux and select Kenmore models.

This replacement coil-cover gasket seals the refrigerator coil/cover area to help maintain proper airflow and reduce dust buildup around the condenser/evaporator cover. Restores the intended fit and helps maintain cooling efficiency. What it does:

• Seals the gap between the coil cover and cabinet to direct airflow over coils
• Helps prevent dust, debris and pet hair from collecting on coils
• Reduces vibration noise by cushioning the cover edge
• Commonly replaced when the gasket is torn, flattened, or missing, or when air leaks are noticed

• Inspect mating surfaces and remove old adhesive/residue before installing for a secure seal
• Use appropriate adhesive or clips if required by your model; follow OEM instructions
• Disconnect power to the appliance before servicing and avoid sharp edges on sheet metal

The Evaporator Fan Motor is an OEM part for Frigidaire refrigerators. It circulates air over the evaporator coils and throughout the refrigerator and freezer compartments, ensuring even cooling and maintaining the desired temperatures.

Causes of a bad evaporator fan motor can include general wear and tear over time, electrical failures such as shorts or blown fuses, or physical damage from ice buildup or debris.

Symptoms of a bad evaporator fan motor include:

• Refrigerator or freezer not cooling properly
• Unusual noises coming from the freezer compartment
• Frost buildup on the evaporator coils
• Inconsistent temperatures within the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This light assembly replaces a damaged or non-working interior fridge lamp to restore safe, even illumination so you can find food and check temperatures. Designed to match the original fit and electrical connection. What it does:

• Provides interior lighting when the refrigerator door is opened
• Replaces cracked lens, damaged socket, or a loose housing that causes flickering or no light
• Helps improve visibility for shelves, drawers and controls near the light
• Works with the existing bulb and wiring harness used by the original assembly

• Disconnect power to the appliance before starting any repair
• Remove the old lens/housing per your model's service instructions and unplug the connector from the socket
• Handle bulbs and lens carefully to avoid breakage; wear gloves and eye protection

This interior refrigerator lamp provides replacement lighting for the fresh-food compartment so you can see contents clearly and check temperature/food without fumbling in the dark. What it does:

• Replaces a burned-out or flickering interior fridge light so the compartment is illuminated
• Helps you quickly find items and inspect food condition without opening the door longer than necessary
• Restores normal operation when the light does not turn on or is dim
• Fits into the fridge's interior lamp socket and functions with the existing switch assembly

• Disconnect power to the appliance before replacing the lamp to avoid shock
• Allow the old bulb to cool before removing; use a cloth or gloves to handle the new bulb
• Install only the correct lamp type for your model; do not force or overtighten the bulb

This is a replacement screw fastener used to secure panels, trim, or components on compatible Frigidaire appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or trim pieces to keep components aligned and stable
• Prevents rattling, vibration noise, and gaps caused by missing or loose fasteners
• Restores proper assembly after service or part replacement
• Helps maintain safety by keeping covers and guards firmly attached

• One screw (single fastener)

• Disconnect power or unplug the appliance before servicing
• Use the appropriate driver to avoid stripping the head; do not overtighten
• Verify the screw matches the original in length and thread before installing

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement screw secures select refrigerator door handles to the door. A worn or missing screw can leave the handle loose or detached, making the door difficult to open and potentially stressing other components.

• Holds the door handle firmly to the door
• Helps restore proper door operation and safe grip
• Designed to fit designated mounting points for compatible models

• Unplug the refrigerator before beginning work
• Open the door to access the handle mounting points
• Use the correct screwdriver/Allen tool to avoid stripping the head
• Start threads by hand and tighten snugly—do not overtighten

This hinge assembly supports and lets your refrigerator door pivot smoothly, restoring proper alignment and reliable closing. It replaces a worn, bent, or broken hinge to reduce door sag, rubbing, or noisy operation. What it does:

• Provides the pivot point for the refrigerator door so it opens and closes correctly
• Restores proper door alignment to help seals meet the cabinet and maintain a tight closure
• Stops or reduces door sag, scraping, and uneven gaps
• Eliminates clicking or grinding noises caused by a damaged hinge

• Unplug the appliance and remove food and shelves as needed before starting
• Support the door while removing and installing the hinge to prevent damage or injury
• Use the correct tools and follow OEM alignment steps; tighten fasteners securely but do not overtighten

This hinge assembly secures and guides the refrigerator door so it opens and closes smoothly. Replacing a worn or damaged hinge restores proper door alignment and helps the seal engage for better cooling performance. What it does:

• Supports the refrigerator door and keeps it aligned on the cabinet
• Guides smooth opening and closing to prevent sagging or binding
• Helps maintain a consistent door seal to reduce air leaks
• Stops excessive noise or scraping caused by worn hinge components

• One hinge assembly

• Unplug the appliance and empty or support the door before starting
• Use proper tools and follow manufacturer instructions; a second person may be needed to hold the door
• Inspect surrounding mounting points and hardware; replace any stripped screws or damaged brackets

This hinge bracket secures and supports a refrigerator door hinge assembly so the door opens and closes smoothly and stays aligned. Replaces a worn or broken bracket to restore proper door fit and operation. What it does:

• Supports the door hinge assembly and keeps the door aligned
• Helps prevent door sag, uneven gaps, or doors that rub or scrape the cabinet
• Restores stable pivoting for smooth opening and closing
• Works with the hinge hardware to maintain proper door seal and cold retention

• Before beginning, empty the door and support it to prevent dropping; consider a helper for heavy doors
• Disconnect power to the appliance if instructed by the manufacturer for your model
• Use basic hand tools; tighten fasteners securely but avoid over-torquing
• If hinge hardware or pins are damaged, inspect and replace as needed for safe operation

This replacement cover protects the refrigerator control panel and internal components while restoring a finished look. It keeps switches and wiring shielded from spills, dust and accidental contact for safe, reliable operation. What it does

• Covers and protects control panel area and related components
• Helps prevent moisture, food debris and accidental contact with switches or wiring
• Restores finished appearance when original cover is cracked, broken or missing
• Compatible with factory mounting points for a secure fit

• One replacement cover

• Disconnect power to the appliance before replacing any parts
• Remove any retaining screws or clips and gently lift old cover away from mounting points
• Align new cover with mounting tabs and secure with the original fasteners
• Inspect adjacent components for damage and replace as needed

Specs: Hex head ,1/4-20 x 5/8

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

Hex washer head ,10-32 x 0.375. Ground

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

The Temperature Sensor (10K NTC) is an OEM replacement part for Frigidaire refrigerators. This sensor monitors the internal temperature of the refrigerator or freezer compartment, sending signals to the control board to regulate cooling cycles. It ensures the appliance maintains the correct temperature for optimal food preservation.

Temperature sensors can fail due to wear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can cause inaccurate temperature readings, leading to improper cooling or freezing.

Symptoms of a bad temperature sensor include:

• Fluctuating or incorrect temperatures in the refrigerator or freezer
• Food spoiling faster than expected or freezing inappropriately
• Error codes related to temperature regulation
• The refrigerator running continuously or cycling too often

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a replacement outer housing cover that restores the appliance's exterior protection and appearance. It shields internal components from debris and helps maintain a finished look for the unit. What it does:

• Covers and protects internal components from dust, dirt and incidental contact
• Restores a clean, finished exterior where the original cover was cracked, warped or missing
• Helps prevent small objects from falling into internal openings
• Reduces visible wear on the appliance for a neater installation

• Disconnect power to the appliance before starting any work
• Remove any retaining screws or clips holding the old cover in place; lift or slide out gently
• Align the replacement cover carefully and re-secure with original hardware

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This push-button door light switch controls the refrigerator interior lamp when the door opens and closes, restoring proper lighting for safe food access. It replaces a worn or failed switch to stop the light from staying on or staying off. What it does

• Opens and closes the lamp circuit when the door is opened or closed so the interior light turns on only when needed.
• Commonly used when the light does not turn on with the door or remains lit continuously.
• Restores normal door-controlled lighting without replacing the entire lamp assembly.
• Functions as the user-actuated contact for the refrigerator interior lamp.

• One push-button door light switch

• Disconnect power to the appliance before beginning any work.
• Access typically through the light housing or door frame; some models require removing the lamp cover.
• Handle bulbs and plastic trim carefully to avoid damage; retain mounting clips and screws for reassembly.

The Thermistor is an OEM part for Frigidaire refrigerators and freezers, designed to accurately monitor and control the temperature within the appliance. This sensitive component reacts to temperature changes by altering its resistance, providing feedback to the control board to regulate the cooling and defrost cycles.  

Causes of thermistor failure can include physical damage, electrical failures within the circuit, or aging, which affects its accuracy and responsiveness.

Symptoms of a bad Thermistor include:

• Unusual temperature fluctuations in the refrigerator or freezer
• The appliance is constantly running or not cooling efficiently
• Error codes displayed on the refrigerator's control panel indicating thermistor problems
• Buildup of frost in the freezer or condensation in the fridge

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Frig PureAir AF2 Air Filter C6 is an OEM replacement part for Frigidaire refrigerators. Installed inside the refrigerator compartment, this filter helps scrub the air to promote fresher flavors and texture retention of stored foods. The washable MERV 6 filter provides up to 3 months of continuous purification.

Causes of a faulty air filter can be debris accumulation over time, blocking clean airflow within the fridge.

Symptoms of a clogged filter include:

• Elevated temperatures inside the refrigerator
• Items drying out or spoiling faster
• Dust or odors detectable on shelves and in crispers
• Diminished filtration performance

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, and some Kenmore refrigerator models.

This mounting bracket secures appliance components to the cabinet frame, restoring solid support and alignment. It's a straightforward replacement for worn, bent, or broken brackets that cause loose panels or misaligned doors. What it does:

• Provides structural support for interior or exterior panels and components
• Helps stop rattling or vibration caused by a loose or damaged bracket
• Restores proper alignment to doors or trim that shift due to bracket failure
• Used wherever a small metal bracket fastens parts to the appliance frame

• One mounting bracket

• Disconnect power to the appliance before servicing to avoid shock or injury
• Installation typically requires basic hand tools; keep fasteners for reuse unless replacement specified
• Handle edges and metal parts carefully to avoid cuts; consider gloves

This freezer air duct directs cold air from the evaporator fan through the freezer compartment, helping maintain steady temperatures and airflow. Replace a cracked, warped, or missing duct to restore consistent cooling and reduce frost or noise. What it does:

• Channels air from the evaporator fan outlet to the freezer vents for even cooling
• Helps maintain targeted freezer temperature and proper circulation
• A damaged or loose duct may contribute to weak airflow, frost buildup near vents, temperature swings, or rattling noises
• Seals the airflow path when properly seated to minimize leaks and hotspots

• 1 freezer air duct

• Disconnect power to the refrigerator before servicing
• Clear the freezer and remove any panels, shelves, or the ice bin as needed for access
• Remove mounting screws or clips, note seal orientation, and seat the new duct fully
• Reuse original hardware, restore power, and verify airflow from the vents

This cover is a replacement protective trim piece that shields internal components and restores the appliance's finished appearance. It helps keep parts protected from dirt while improving the unit's look. What it does

• Protects exposed components and wiring from dust and debris
• Restores damaged or missing exterior trim for a finished appearance
• Helps prevent accidental contact with internal parts
• Commonly replaced when cracked, broken, or missing

• One appliance cover as pictured and specified by the manufacturer

• Disconnect power to the appliance before starting any service
• Typically attaches with clips or screws; use appropriate tools and keep fasteners
• Handle carefully to avoid scratching the replacement part

This grille clip is a small plastic retainer that secures a refrigerator grille or trim piece to the cabinet, keeping the front panels aligned and preventing rattles or gaps for a tidy appearance. What it does:

• Secures the lower/front grille or trim to the appliance cabinet to hold it in place
• Prevents grille movement, rattling, or sagging that can occur with worn clips
• Helps maintain a tight fit between trim and cabinet for a finished look
• Simple replacement part when existing clip is cracked, broken, or missing

• One grille clip

• Typically snaps into place; inspect mating slot and clip orientation before installing
• Replace any damaged adjacent clips for even support and fit
• Work carefully to avoid damaging the grille or surrounding trim

This genuine replacement screw restores a secure hold for panels, trim, or internal components. It replaces worn or missing fasteners so parts stay aligned and appliances operate safely. What it does:

• Fastens panels, brackets, or trim into place
• Replaces stripped, missing, or damaged screws
• Helps stop rattling, loose panels, or misaligned trim
• Fits OEM mounting locations that require the specified machine screw

• Use the correct driver to avoid stripping the head
• Hand-start the screw, then tighten to firm snug; do not over-torque
• Disconnect power to the appliance before accessing internal components
• If other fasteners are damaged, inspect and replace as needed

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing