Parts for Frigidaire PRFC2383AF1: Controls & Ice Dispenser Parts

The Water Tube is an OEM part for Frigidaire refrigerators. It is a flexible plastic tube that transports water from the refrigerator's water valve to the dispensing system within the door.

Over time, constant flexing and humidity exposure can cause cracks and splits to form within the water tube. Mineral buildup may also restrict flow. Please note, this part does not include mounting brackets or clips.

Causes of a bad tube can be wear and tear, piercing from sharp shelf edges, or damage incurred during repairs.  

Symptoms of a bad water tube include:

• Leaks or drips of water inside the refrigerator
• Slow water flow or intermittent water flow from the dispenser
• Dispenser unable to produce water or ice

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This housing is the main structural enclosure that supports and protects internal components, restoring proper alignment and safe operation. It replaces a damaged or cracked outer housing to reduce vibration and protect wiring and moving parts. What it does

• Provides structural support and mounting points for internal components.
• Protects internal parts from debris and physical damage.
• Helps reduce vibration and rattling caused by a cracked or broken housing.
• Restores proper alignment to maintain correct component clearances.

• One housing main assembly.

• Disconnect power and, if applicable, gas supply before starting any repair.
• Handle carefully to avoid damaging mounting tabs or paint; some trimming may be required for perfect fit on older units.
• If any fasteners, clips, or gaskets are worn or missing, replace them to ensure a secure installation.

This plastic guide positions and supports a moving component inside the appliance to keep parts aligned and running smoothly. Replacing a worn guide restores proper fit and helps reduce rubbing noises and uneven movement. What it does:

• Holds and aligns a moving part or trim so it tracks correctly during operation
• Prevents rubbing, scraping, or binding that can cause noise or premature wear
• Maintains correct spacing to protect adjacent components from damage
• Commonly replaced when you see misalignment, clicking, or intermittent contact

• One plastic guide as shown

• Disconnect power (and water, if applicable) before attempting any repair
• Access may require removing panels or trim; keep fasteners organized
• Inspect adjacent parts for wear and replace if needed to prevent repeat failure

This electronic control is the main user interface and control board for the oven, managing cooking functions, timing, and display features for compatible ranges. Replaces a failed or unresponsive control to restore normal oven operation. What it does:

• Manages oven functions such as bake, broil, timers, and temperature control signals
• Processes keypad/selector inputs and updates the display or status indicators
• Sends control commands to heating elements, relays, and temperature sensors
• Commonly replaces controls that cause unresponsive buttons, incorrect timers, or display errors

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the board carefully to avoid static damage; use an anti-static wrist strap if available
• Follow OEM disassembly steps for console removal and secure all connectors in their original positions

This dispenser actuator is the user-facing lever that engages the refrigerator's water/ice dispenser. A stainless finish provides a clean look while restoring reliable push-to-dispense operation. What it does:

• Replaces a broken, cracked or worn dispenser lever so the dispenser responds when pressed
• Transfers user force to the dispenser switch/valve to start water or ice dispensing
• Helps stop leaks and jams caused by a misaligned or damaged actuator
• Restores correct alignment of the dispenser paddle for smooth operation

• One stainless dispenser actuator

• Disconnect power to the refrigerator before starting any repair
• Remove the dispenser bezel/panel per your model's service instructions to access the actuator
• Handle plastic tabs carefully; work in a well-lit area and keep small fasteners secure

This tension spring provides the restoring force needed for a moving refrigerator component, helping parts return to their normal position for reliable operation and alignment. It's a simple replacement that restores proper movement and stability. What it does:

• Provides tension to return or hold a component in place during normal operation
• Helps maintain proper alignment and smooth movement of the associated mechanism
• Worn or broken springs can cause improper latching, sagging, or uneven movement
• Replacing a damaged spring often resolves related noise or binding issues

• One replacement spring

• Disconnect power before attempting any repairs to avoid electrical hazards
• Handle springs carefully; they can be under tension and may require basic tools to remove/install
• Replace with the exact part number to ensure fit and function

This is a replacement appliance switch used to complete or interrupt a circuit for lights, controls, or safety features. It restores proper on/off function so features respond when the switch is pressed or released. What it does:

• Acts as a user-operated electrical contact to turn a circuit on or off
• Commonly used for door lights, control panels, or interlock functions
• Works as a direct mechanical/electrical replacement when the original switch fails

• One replacement switch

• Disconnect power to the appliance before attempting replacement
• Verify orientation and connector fit; do not force terminals
• Dispose of the old switch per local electronic-waste guidelines

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

Color: Black/natural. Nylon

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This dispenser wiring harness connects the dispenser controls and components in the refrigerator door, restoring electrical continuity for the dispenser functions and simplifying replacement of a damaged or faulty harness. What it does:

• Carries power and signals between the dispenser switches, valve/solenoid, and indicator lights
• Replaces frayed, pinched, or damaged wiring that can cause intermittent or no dispenser operation
• Addresses symptoms like non-working water/ice dispenser, no dispenser lights, or unresponsive dispenser switches
• Provides factory-style connectors for a direct, plug-and-play replacement

• One dispenser wiring harness

• Disconnect power to the appliance before beginning any work to avoid shock
• Remove the inner door panel or dispenser bezel per your model's service instructions to access the harness
• Match connectors and routing to the original harness; avoid stretching or pinching wires when reinstalling
• Test dispenser functions after installation and reassemble panels securely

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle