Parts for Kenmore 253.27003411 (25327003411, 253 27003411): Cabinet Parts

Water pooling in freezer? This drain screen traps debris before it clogs the drain tube. Quick snap-in replacement restores proper drainage flow.

Fixes uneven cooling or warm top shelves in freezers. This blower wheel restores proper air circulation when the fan stops moving cold air effectively.

This is a right-side breaker strip that serves as an insulating divider between the freezer and refrigerator compartments or between the inner liner and outer cabinet. It helps maintain proper temperature separation and prevents condensation from forming along the cabinet edges. Replace this strip if it is cracked, warped, or if you notice moisture or frost buildup along the right side of the compartment opening.

This is a plastic breaker strip that fits along the upper area of the freezer compartment, serving as a trim piece that bridges the gap between the inner liner and the outer cabinet. It helps provide insulation and a finished appearance at the top of the freezer. Replace this strip if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup.

This is a lower breaker strip (divider panel) that fits along the interior of the freezer compartment. It serves as a trim piece that covers the gap between the liner and the outer cabinet, helping to insulate and provide a finished appearance. Replace this part if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup or temperature inconsistencies.

Freezer not cooling or running warm? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair typically takes 30-45 minutes.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Light lens cover for refrigerator interior lighting. Replaces cracked, yellowed, or missing lens covers. Snaps into place over bulb compartment.

Powers your refrigerator's interior lighting. Replace when lights dim, flicker, or fail. Confirm fit with your model number before ordering.

Seals the evaporator cover to prevent air leaks, frost buildup, and temperature fluctuations. Replace if worn or cracked. Verify fit with your model.

Creates the angled track for the hinge cam to glide smoothly. Replace when the door sticks, won't open fully, or doesn't self-close. Verify fit by model.

Supports and pivots your freezer door for smooth opening and closing. Replace when worn or bent to restore proper alignment, improve sealing, and prevent air leaks or frost buildup. Confirm fit by model number.

Secures door stop to hinge bracket, controlling opening angle. Replace if pin is bent, broken, or missing to restore smooth door operation.

Carries defrost water from your freezer drain outlet to the drip pan. Replace if cracked, kinked, or detached to prevent leaks onto floors and cabinets.

This drain pipe connects the defrost drain outlet to the drain pan area, channeling condensation and defrost water away from the freezer compartment. It is a rigid or semi-rigid tube that slides into the drain opening and directs water downward. Replace this part if you notice water pooling inside the freezer, ice buildup near the bottom of the compartment, or water leaking onto the floor beneath the appliance.

Cabinet corner trim for freezers. Covers and finishes the corner edges of the cabinet exterior. Replace if cracked, chipped, or missing for a clean look.

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Specs: Hex head ,1/4-20 x 5/8

Secures refrigerator door shelf and restores edge trim for stable storage. Replaces cracked, broken, or worn shelf frame to keep items supported.

Upper glass shelf assembly for freezer interior storage. Replace cracked, chipped, broken, or missing shelves to restore organized food storage space.

Replace a cracked, broken, or missing interior shelf in your freezer. Restores stable storage space for organized food placement inside the cabinet.

Secures internal components and panels in your freezer. Replace this support bracket if it's cracked, broken, or missing to restore proper alignment.

Freezer not cooling, won't start, or cycling incorrectly? The electronic control board directs power to motors, valves, and fans. Moderate DIY repair.

This is a wire or plastic storage basket that slides into the freezer compartment to organize and separate frozen foods. It helps maximize storage space and allows easy access to items stored inside. Replace this basket if it is cracked, warped, has broken rails, or no longer slides smoothly on the tracks.

Secures hanging basket to freezer rack. Replaces broken, bent, or missing hanger to restore proper basket support and prevent sagging or detachment.

Fixes a loose or fallen wire basket inside your freezer. This support bracket secures hanging baskets in place for stable storage. Simple DIY repair.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Replacement screw that secures freezer panels, brackets, and trim. Install when original hardware is missing, stripped, or loose to keep components aligned.

Threaded insert nut creates secure anchor point in thin metal or plastic panels. Replace worn, stripped, or missing insert nuts to properly mount covers.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.

Replacement storage divider for upright freezers. Separates and organizes frozen items. Replace if cracked, broken, or missing to restore compartments.

This corner trim kit replaces damaged or worn decorative corner pieces on the refrigerator door to restore a clean, finished appearance and help protect the door edge. Simple cosmetic repair for chipped, cracked, or loose corner trim. What it does:

• Replaces cracked, broken, or missing door corner trim to improve appearance
• Covers and protects exposed door edge from everyday wear
• Helps restore proper trim alignment and fit around the door corner
• Works with existing door shell and mounting points for a straightforward swap

• Turn off or unplug the appliance and empty the area near the door before starting
• Remove the old trim carefully to avoid scratching the cabinet or door finish
• Align new trim pieces to factory mounting points; secure using original clips or screws
• If any mounting hardware is missing or damaged, replace with OEM-specified hardware

Rubber grommet for freezer interior assembly. Replaces worn, cracked, or missing grommets that secure components or reduce vibration in your unit.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.