Parts for Kenmore 253.70404411 (25370404411, 253 70404411): Cabinet Parts

Replaces cracked, broken, or missing compartment cover in your refrigerator. Restores clean appearance and shields internal components and wiring.

Fixes refrigerator running constantly, freezing food, or not cooling properly. This temperature control assembly monitors cabinet temp and cycles cooling.

Refrigerator not cooling but freezer works? This evaporator fan cover and damper assembly directs airflow between compartments. Moderate DIY repair.

Refrigerator not cooling but freezer works? Broken evaporator fan blade stops cold air circulation. Easy DIY fix in under an hour with basic tools.

Securing ring holds components in position within your refrigerator assembly. Replace if worn, damaged, or missing to restore proper fit and alignment.

Seals openings where tubes or wires pass through your refrigerator cabinet. Replace if cracked, torn, or causing air leaks. Confirm fit with your model.

If your refrigerator fan rattles or vibrates loudly, this evaporator fan motor grommet cushions the motor mount and stops the noise. Quick DIY fix.

Mounting bracket that secures the shroud or cover to your refrigerator cabinet. Replace this bracket if cracked, bent, or broken to restore alignment.

Refrigerator not cooling but freezer works? A failed evaporator fan motor stops cold air circulation. This DIY repair takes 10-15 minutes with basic tools.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Black button plug that covers upper hinge mounting holes on your refrigerator. Replace if original plug is missing, cracked, or broken for a clean finish.

White plastic button plug that covers unused hinge holes on refrigerator doors. Replace if cracked, missing, or discolored for a clean finished look.

Lower hinge bracket secures the refrigerator door at the bottom, allowing smooth pivoting. Replace if bent, cracked, or causing door misalignment and sagging.

Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.

Center hinge bracket for refrigerator doors in bisque finish. Replaces broken, cracked, or worn hinge brackets. Mounts between upper and lower doors.

Black center hinge bracket mounts between refrigerator doors to support and align them. Replace if bent, cracked, or worn to restore proper door swing.

Center hinge bracket mounts between refrigerator doors at the middle hinge location. Replace if cracked, broken, or missing to secure door alignment.

Sits on the center hinge pin to maintain proper door spacing and smooth pivoting. Replace if worn, cracked, or missing to restore even door alignment.

Supports and pivots the refrigerator door at the center hinge bracket. Replace if worn, damaged, or missing to restore smooth door swing and alignment.

Replaces damaged or missing corner trim where cabinet panels meet on your refrigerator. Restores finished appearance and protects edges from wear.

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

Secures the top of your refrigerator door to the cabinet. Replace if cracked, broken, bent, or lost during a move to restore proper door alignment.

Black upper hinge cover conceals and protects your refrigerator's door hinge assembly. Replace if cracked, broken, or missing to restore appearance.

White plastic cover that snaps onto the upper door hinge. Replace if cracked, broken, or missing to restore a finished look to your refrigerator.

Replacement shelf support grommet for refrigerators and freezers. Provides stability for shelves. Replace if broken, missing, or worn to restore proper shelf support.

Mounting screw for refrigerator components. Replaces lost, stripped, or damaged screws. Essential hardware for securing panels and brackets.

Replacement mounting screw for refrigerator panels, brackets, and trim assemblies. Needed when original fastener is stripped, missing, or broken.

Specs: Hex head ,1/4-20 x 5/8

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

Replacement lower hinge pin for refrigerator doors. Acts as a pivot point to hang and support the door. Replace if worn, broken, or missing from a move.

Replace missing or stripped #10-32 x 3/4" screws that secure panels, brackets, and trim on refrigerators. Restores tight fit and eliminates rattles.

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

Black lower front grille kickplate for refrigerators. Covers and protects the bottom front opening. Replace if cracked, broken, or missing.

Black lower front grille kickplate for refrigerators. Covers and protects the bottom front opening. Replace if cracked, broken, or missing.

White grille kickplate for refrigerators. Covers the bottom front panel beneath the door. Replace if cracked, broken, or missing for a finished look.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Replacement access cover panel for refrigerators. Closes service openings and protects internal components. Needed when original is cracked or missing.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Replacement front roller assembly for refrigerators. Includes leveling screw. Needed when roller is cracked, broken, or leveling screw is bent or damaged.

Restores tight seals to stop leaks, drafts, and temperature loss. Replace when you notice gaps, noise, or moisture issues. Verify fit with your model.

This wiring harness routes electrical power/signals between refrigerator components. Replacing a damaged harness helps restore reliable connections so fans, sensors, lights, or the icemaker receive proper power and communication.

• Connects internal refrigerator components to the main wiring circuit
• Can help when there are intermittent power issues to fans, lights, or icemaker
• Designed to fit specific layouts; match connectors to your original for compatibility

• Disconnect power before servicing to avoid electrical shock
• Take photos of existing connector locations to ensure correct reassembly
• Handle connectors by the housings; avoid pulling on wires
• If connectors don't seat easily, re-check orientation—do not force

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head