Parts for Kitchenaid KRFC704FSS00: 02 - Cabinet Parts

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

This pivot block is a small mounting support that holds a pivot or hinge shaft in place, restoring proper alignment and smooth movement for the moving assembly. It's a direct-replacement mechanical support piece. What it does:

• Supports and stabilizes a pivoting shaft or hinge so the assembly moves smoothly
• Prevents excessive play or misalignment that can cause rubbing, grinding, or uneven motion
• Helps reduce vibration and noise coming from a loose or worn pivot point
• Restores proper component positioning so doors, drums, or linkages close and operate correctly

• One pivot block

• Disconnect power to the appliance before starting any repair
• Access may require removing a panel or trim; keep track of fasteners and fastener locations
• Use basic hand tools; avoid forcing parts—replace any damaged clips or fasteners
• Check adjacent parts (shaft, bushing, or bracket) for wear

This electronic control board is the appliance's central processor, managing power and timing to critical components. It helps restore normal operation when the original board fails, leading to no response, error codes, or erratic behavior.

• Directs cycle timing and power to motors, valves, heaters, fans, and lights as designed
• Interprets inputs from the user interface and sensors to run selected functions
• Monitors safety circuits and stores/communicates fault codes
• Typical failure symptoms: dead/no response, will not start or complete a cycle, intermittent operation, error codes or random beeps/chimes

• Disconnect power at the breaker before servicing; verify power is off
• Use ESD precautions; handle the board by the edges to avoid static damage
• Photograph connectors; transfer any jumpers, brackets, or housings from the original board
• After installation, run service diagnostics or setup per the tech sheet/service manual

This cabinet roller replaces a worn or broken roller that helps a drawer or cabinet glide smoothly. Restores proper tracking and reduces sticking or grinding for easy opening and closing. What it does:

• Supports and guides the drawer/cabinet along its track for smooth movement
• Replaces damaged or worn rollers that cause sticking, binding, or uneven travel
• Reduces noise from grinding or scraping when opening or closing
• Helps prevent drawer misalignment and uneven wear on the track

• Inspect the track and mounting clips for damage; replace any broken components
• Remove power to nearby appliances and work with the drawer empty
• Use basic hand tools; avoid forcing parts—ensure the roller is seated fully in its bracket

This cabinet roller replaces a worn or broken roller to restore smooth opening and closing of the appliance drawer or cabinet. It reduces noise and sticking for improved everyday use. What it does:

• Replaces a damaged or worn cabinet/drawer roller to restore smooth gliding motion
• Reduces squeaking, sticking, or uneven travel when opening or closing the drawer
• Supports proper alignment of the drawer or rack during operation
• Helps prevent further wear to tracks and mounting hardware by restoring correct movement

• Disconnect power to the appliance before beginning any repair
• Remove the drawer or access panel to reach the roller; keep fasteners organized
• Inspect the track and mounting clip for damage; replace damaged hardware if found
• Reassemble and test drawer travel; no special tools typically required, but a screwdriver or pliers may help

This adjustable leveler threads into the base of your appliance to set height and keep it stable. Replacing a worn or missing leg helps reduce wobble and vibration and restores proper leveling for smooth, reliable operation. What it does:

• Threads into the cabinet base to fine-tune height and level front-to-back and side-to-side
• Helps reduce rocking, vibration, and rattling noises during use
• Can improve alignment and closure on units that are out of level
• Common failure signs include a cracked foot, stripped threads, or a missing leg

• One leveler

• Disconnect power; turn off water supply if applicable before moving the appliance
• Use a helper and protect flooring when tilting or positioning the unit
• Start threads by hand to avoid cross-threading; finish adjustment with a wrench as needed
• Level all corners until stable; recheck after loading or repositioning the appliance

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This door hinge secures and allows smooth pivoting of a refrigerator or freezer door so it opens and closes correctly, helping maintain a proper seal and consistent cooling performance. What it does

• Supports the door weight and provides a stable pivot point for opening and closing
• Keeps the door aligned to ensure the gasket seals properly and reduce cold-air loss
• Helps prevent door sag, rubbing, and uneven wear that can cause noise or poor sealing
• Replaces a worn, bent, or damaged hinge to restore proper door movement

• One door hinge

• Installation requires removing the door or supporting it to avoid damage
• Use proper tools and torque; tighten fasteners securely but avoid over-torquing
• Disconnect power to the appliance before working if panels or wiring must be removed
• If the hinge mounts use separate screws or bushings, transfer existing hardware unless OEM kit specifies otherwise

This replacement cover restores a finished, secure opening on the appliance and protects internal components from dust, moisture, and accidental contact. It fits the original mounting points for a factory-like repair. What it does:

• Replaces a cracked, broken, or missing cover to restore the appliance's exterior protection
• Shields wiring, controls, or internal parts from dust and debris
• Helps prevent accidental contact with internal components that could cause damage or shorting
• Restores a clean appearance and proper alignment of the adjacent panels

• Disconnect power to the appliance before beginning any repair
• Installation typically requires removing the surrounding trim or panel and fastening the cover with the original screws
• Handle carefully to avoid scratching the finish; align mounting tabs before tightening

The Hinge Cover is an OEM component used in Whirlpool refrigerators. It is a sleek plastic cover that fits neatly over the hinge pins and mounting bracket of the refrigerator door. 

Causes of a bad hinge cover include cracks or breaks from accidental impact over time. Normal wear and exposure to household elements can also cause fading or discoloration of plastic.

Symptoms of a defective hinge cover are:

• Exposure of internal mounting hardware   
• Gaps appearing where the cover once fit
• An undesirable appearance around the doorframe

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cover is an access panel that protects internal appliance components and helps keep dust, lint, and debris out while maintaining the appliance's finished appearance. It provides a safe, stable mounting surface for nearby parts. What it does:

• Covers and protects internal components from debris and accidental contact
• Helps maintain proper airflow paths and prevents lint buildup in service areas
• Preserves the appliance's exterior finish and appearance
• Provides a location for mounting adjacent parts or fasteners

• One cover

• Disconnect power (and gas, if applicable) before starting any repair
• Use appropriate hand tools and retain all fasteners for reassembly
• Handle edges carefully; wear gloves to avoid cuts
• Follow the appliance's service manual for correct removal and torque specs

This replacement valve cover protects and secures the washer's inlet valve assembly, helping keep water and wiring contained and reducing risk of leaks or damage. It restores the valve area's original shielding and fit. What it does:

• Covers and protects the water inlet/valve area from splashes and debris
• Helps keep valve wiring and connections properly routed and contained
• Can stop water spray from a damaged or misaligned valve area
• Restores correct mounting/fit to prevent valve movement and noise

• One replacement valve cover

• Disconnect power and shut off water before starting any repair
• Basic hand tools are typically required; access may require removing the top or control panel
• Align cover tabs and secure fasteners until snug; do not overtighten
• Inspect nearby seals, hoses and valve connections while accessible

This replacement screw fastens appliance components to restore secure connections and reduce vibration or rattling. Use it when panels, brackets, or assemblies are loose or moving. What it does:

• Secures panels, brackets, and small appliance parts to prevent movement
• Restores proper alignment for doors and trim that shift from loose hardware
• Helps eliminate vibration noise caused by loose fasteners
• Works with assemblies that use standard machine/sheet-metal screws

• Disconnect power or gas supply before servicing the appliance
• Use the correct driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or damage parts
• Inspect surrounding components and replace any damaged clips or hardware as needed

Color: Black
 

This door hinge assembly secures and guides the appliance door, restoring proper door alignment and smooth opening and closing. It's a direct-fit replacement that helps stop sagging, rubbing, or difficulty latching. What it does:

• Supports the door on its pivot so the door opens and closes smoothly.
• Restores proper door alignment to improve sealing and prevent gaps.
• Stops door sag, dragging on the cabinet, or uneven closing.
• Works as a direct replacement for the original hinge design.

• Disconnect power to the appliance before starting and follow the manufacturer's safety instructions.
• Use appropriate tools; some models require removing the door or adjusting mounting screws during installation.
• Handle the door carefully to avoid dropping or damaging the hinges or door surface.

This door hinge is a direct-fit replacement that helps the refrigerator door open and close smoothly and keeps the door aligned to seal properly. Restores proper door movement and helps prevent gaps that can cause cooling loss. What it does:

• Provides the pivot point for the refrigerator door, enabling smooth opening and closing
• Maintains door alignment to help the gasket seal evenly and preserve internal temperature
• Replaces worn, bent, or broken hinges that cause sagging, scraping, or noisy operation
• Helps prevent uneven wear on the door and stops abnormal rubbing against the cabinet

• One replacement door hinge

• Designed to mount in the original hinge location; hardware may be required if original fasteners are damaged
• Power off the appliance and remove contents from the door area as needed for safe access
• Support the door during removal/installation to avoid damage or personal injury

Color: Black

This black plastic corner cover replaces a damaged or missing exterior trim piece to restore the appliance's finished appearance and protect internal edges from dirt and wear. Fits the factory location and matches original styling. What it does:

• Covers and protects the appliance corner or trim area from chips, scuffs, and debris.
• Restores a clean, finished look where the original corner piece is cracked, broken, or missing.
• Helps keep moisture and grime from reaching internal seams at the corner.
• Matches the original color and shape to maintain the appliance's aesthetic.

• Install with the appliance powered off and unplugged for safety if cover removal exposes wiring.
• Remove any broken fragments and clean the mounting area before installing the new cover.
• May snap or screw into place depending on model; keep fasteners from the original cover for re-use.

This replacement switch restores the electrical control function for the appliance, letting the associated component respond correctly when activated. It provides a straightforward swap to return reliable on/off or sensing operation. What it does:

• Opens or closes an electrical circuit to control power to a specific component.
• Stops or allows a component to run when the switch is operated (safe symptom linkage: appliance won't start, a specific function won't respond, or an interior light/motor won't operate).
• Matches the original mounting and terminal locations for a direct replacement when this exact part number is required.
• Works as the user-replaceable control switch for the affected function.

• Always disconnect power to the appliance before beginning service.
• Handle terminals carefully and make secure electrical connections; avoid bending or damaging pins.
• After installation, restore power and test the appliance operation to confirm proper function.

This replacement divider restores organization inside the refrigerator drawer so groceries stay separated and upright for easier access. It's a simple, low-profile plastic divider that helps prevent items from shifting during normal use. What it does

• Separates and organizes items inside a refrigerator or freezer drawer
• Keeps produce, deli items, or packaged goods from sliding together
• Helps maintain tidy storage for easier access and loading
• Fits into existing drawer tracks or slots to hold position during normal use

• Remove the drawer before installing to access the divider slots more easily
• Slide the divider into the matching tracks or slots until it seats securely
• Do not force or bend the part; verify orientation matches the opposite side or clips
• For safety, work with dry hands and stable drawer positioning; unplug appliance only if instructed by appliance-specific service manual

This is a genuine mounting screw used to secure appliance panels and components. It provides reliable fastening to keep parts aligned and reduce vibration-related noise for safer, quieter operation. What it does:

• Secures panels, brackets, or small components to the appliance frame
• Prevents parts from loosening and causing rattling or misalignment
• Maintains proper part positioning for reliable operation
• Helps reduce vibration and noise when panels are fastened correctly

• Use the correct driver and size to avoid stripping the head
• Tighten until snug; do not overtighten which can strip threads or crack plastic
• Disconnect power before servicing electrical appliances to avoid shock
• If a screw is corroded or damaged, replace all similar fasteners in that area for best results

This replacement vent directs airflow from the appliance's blower to the outside or into the vent duct, helping maintain proper exhaust and drying performance. Fits where the OEM vent assembly is required for safe, efficient operation. What it does:

• Channels exhaust air from the appliance to the duct system to prevent backflow and moisture buildup.
• Restores proper ventilation when a cracked, damaged, or missing vent causes poor airflow or noisy operation.
• Helps reduce lint and debris escape into the cabinet area by providing the correct outlet path.
• Supports normal drying/heating performance by maintaining intended airflow routing.

• 1 vent

• Turn off and unplug the appliance (or shut off power at the breaker) before beginning any work.
• Remove any surrounding panels or access covers to reach the vent; follow manufacturer service instructions for disassembly.
• Inspect mating ductwork and seals; replace damaged ducts or use approved clamps/adhesive to ensure an airtight connection.

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

This rubber grommet cushions and protects a mounting or wiring pass-through, helping reduce vibration and prevent chafing where parts or wires pass through a panel. It's a simple replacement that restores a secure, quiet fit. What it does:

• Provides a protective barrier around openings to prevent wire and component abrasion
• Cushions panels or components to reduce noise and vibration
• Helps maintain proper alignment of mounted parts
• Commonly replaced when torn, flattened, or allowing rubbing/metal-to-metal contact

• One rubber grommet as shown

• High-level replacement — access to the panel or opening is required
• Inspect surrounding fasteners and wiring for damage while replacing
• Use basic hand tools; avoid stretching the grommet excessively during installation
• Disconnect power to the appliance before working in areas with wiring or motors

The Hinge Bushing is an OEM component specifically designed for Whirlpool refrigerator doors. It is a circular bearing and support component that promotes smooth door swinging. The bushing fits within hinges to reduce friction and prevent premature wear.  

Causes of compromised hinge bushings can be years of door opening compressing the bushing material. Exposure to moisture also contributes to cracked, pitted or damaged bushings failing to guide doors effortlessly.

Symptoms of failing hinge bushings include:

• Stiff or resistant door movement requiring extra effort  
• Noisy hinges or grinding sounds due to metal-on-metal contact
• Misaligned or sagging doors unable to fully latch or seal
• Premature wear of connecting hinge parts forcing early replacement

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.