Need Help?
Call or text
This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.
Turned off breaker,unscrewed (2 screws) element,pulled element out from back of oven,unplugged 2 wires, attached wires to new element, pushed back in, installed retaining screws Read more
Charcoal filter absorbs cooking odors in recirculating range hoods. Replace every 6 months for effective odor control. Verify fit by model number.
Called & ordered, new screen arrived, popped it in and all set. Read more
Range burner not heating? This 8-inch surface element restores even heating to your cooktop. Simple plug-in replacement takes under 10 minutes with no tools.
I unplugged the old, plugged in the new, and started cooking. Read more
Burner stuck on high or won't heat? The infinite switch controls surface element power from low to high. Common DIY fix restores heat adjustment.
Replaced infinite switch Read more
This is a start switch intended for use with dryers. With time or because of damage caused by accident, the start switch may stop working correctly. If the start switch isn't working, then the dryer will not function properly, and a replacement part should be ordered. If the push to start switch doesn't respond, it could be damaged or broken. Replacing the push to start switch on a dryer is a simple process. Start by unplugging the machine. Remove the back panel and pull out the old push to start button. Put the new button in its place and reattach the rear panel. Wear gloves for protection. Restore power only after the complete reassembly is performed. This push-to-start button is a genuine OEM replacement part. It is sold as an individual unit. The part is sourced from the manufacturer and made of durable materials. The push-to-start button can be installed in various dryer models made by SpeedQueen and Alliance brands.
Glass scraper tool for cleaning cooktop surfaces. Removes stuck-on food, spills, and residue from glass cooktops. Essential for maintaining appearance.
Remove unit, remove about 12 screw holding the top to the unit switch the tops reverse steps and done Read more
To order indicator lens use WP22001948.
Mounts in the dispenser to secure the ice housing assembly. Keeps the chute and door aligned for smooth dispensing. Replace if cracked, broken, or worn.
Replaced the ice tray and motor mount plate. While I was there I replaced the thermostat also. New parts arrived in a day and a half. Read more
This square drip pan is used on gas ranges. Color: chrome. It measures about 8 inches wide by 8 inches deep.
I ordered 4 new grates along with 4 chrome top burner drip pans. They were a perfect fit and have returned an old stove to to a look of almost-new! Read more
Burner won't turn down from high or stays on? This infinite switch regulates heat to surface elements. Common DIY fix for overheating burners.
I immediately took the cooktop apart, found the bad part, and got the part number. I went online to AppliancePartsPros and typed in the model number, found the part and ordered it on a Sunday evening. The part arrived on Wednesday and I installed it that night and we were good to go! Read more
Replace a burner that won't heat or heats unevenly with this 6-inch surface element. Compatible with electric ranges and cooktops. DIY-friendly install.
We had ordered and installed the drip pans and when we took a look, we knew we needed new elements. Those were perfect; exact replacement. The problem was on the eight inch units, the rim of the drip pan touched the element. It was a simple matter of removing a small bit of the drip pan where the element enters. Aircraft snips and a little polishing with a Dremel tool, and all is well. Wife loves the new elements. Read more
Screw: 8-16 x 3/8 inch.
Broiler not heating or browning evenly? This broil element restores intense overhead heat for proper broiling. Easy DIY replacement with basic tools.
I got a new element, watched the video on AppliancePartsPro.com on how to take out the old one and replace it with the new one. It all went great (thanks to the video). I don't think I could have done it without the video. Read more
Thermostat knob mounts on the control shaft to adjust temperature settings. Replace a cracked, stripped, or missing knob to restore control of your range.
Size: 26 inches long. F18t8/cw/k26.
I replaced the controller. I had a heck of a time figuring out how to get to it. The video on the website showed access to the control via the rear panel. On the Kitchen Aid we have, the back panel is part of the range's main frame and does not come off. Turns out, 2 screws behind the fluorescent lamp had to be removed and the entire control panel housing lifts up and can be tilted forward. (I needed to clean behind the range anyway, so it was no big deal)!! The replacement part instructions... Read more
Burner not heating or heating unevenly? This 6-inch surface coil element restores consistent heat to your electric range. Simple plug-in replacement.
I ordered the parts from this company. Read more