Parts for Lg T1772HFFS: Case Assembly Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Protective cover for washer control panel or component housing. Replaces cracked, broken, or missing covers. Shields internal parts from damage.

Replace your washer's guide cover if it's cracked, broken, or missing. This cover protects the internal guide mechanism and maintains proper operation.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replace your washer's control panel housing case if cracked, broken, or damaged. This protective cover secures and shields internal components.

Secures internal washer components in proper alignment. Replace this mounting bracket if cracked, rusted, broken, or missing to restore stability.

Outer trim piece that finishes your washer door for a clean look and protects components. Replace when damaged, faded, or to restore appearance. Confirm fit with your model number.

Secures internal components to the washer frame. Replace if your bracket is cracked, rusted, broken, or missing to restore stable support and alignment.

This noise filter assembly is an electronic component that suppresses electromagnetic interference generated by the washer's motor and control board. It is typically mounted near the power inlet and helps protect other household electronics from electrical noise. Replace this assembly if your washer fails to start, trips a breaker, or if the filter housing appears burned or damaged.

Replaces a cracked, broken, stripped, or missing control knob on your dryer or washer. Restores secure grip and proper engagement with the control shaft.

Fix a blank, flickering, or unresponsive washer display with this control board. Restores clear readouts and button functionality. DIY-friendly repair.

Leaking water behind your washer? A cracked inlet hose is often the culprit. This hose channels water from your supply line into the machine during fill.

Fix a washer that won't start, cycle, or respond to controls. This main control board restores power distribution and operation coordination.

Replace a cracked or clogged washer nozzle assembly to restore proper water flow and prevent poor cleaning performance. Moderate DIY repair.

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

Fix a leaking or cracked fabric softener dispenser with this washer softener cap. Easy DIY repair with no tools needed—just remove and replace in minutes.

This small cover cap conceals an exposed fastener or opening on your appliance, restoring a clean, finished look. It also helps protect the area from dust and splashes for a tidy, long-lasting installation.

• Covers and protects an open screw hole or attachment point on a panel or door
• Restores a clean, factory appearance
• Helps keep dust and moisture out of the opening
• Common signs it's needed: missing cap, cracked/broken cap, loose cap, won't stay clipped

• Disconnect power (and water, if applicable) before servicing exterior panels or doors
• Note the cap's orientation and any retaining tabs before removal
• Use a plastic pry tool to gently release the old cap; press the new cap until fully seated
• Avoid forcing the cap or overtightening any underlying fastener to prevent damage

Fix dispenser overflow or leaking issues with this washer detergent drawer assembly. Channels water through detergent and softener compartments. DIY repair.

Connects water inlet valve to tub in your washer. Replace if cracked, leaking, or ports are stripped. Ensures secure, leak-proof connection during cycles.

Fix DL error code or washer that won't start with this lid switch and lock assembly. DIY repair in about 20 minutes with basic tools and video guide.

Fix washer overfilling or not filling issues with a water level pressure switch replacement. Common repair for PE error codes. Takes 10-20 minutes to install.

Washer won't fill or won't stop filling? This water inlet valve controls water flow into the tub. DIY-friendly repair, typically takes 10-15 minutes.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.