Parts for Kitchenaid 9KSM3311XVB0: Case, Motor And Planetary Unit Parts

The Hub Cap is an OEM replacement part is for Whirlpool stand mixers. The cap hub is a small part at the top of your mixer which you remove when adding an attachment such as the pastamaker. To replace this part, simply unscrew the knob to the right of the cap, and remove and replace the cap.

Causes of a bad hub cap can include cracks or punctures developing over extended use periods. Excessive downward force on heavy mixing attachments may also damage the cap over time.

Symptoms of a bad hub cap include:

• Fluids leaking into the base or motor areas during mixing
• Moisture or messes within the stand mixer body
• Inability to maintain suction or vacuum when using attachments

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and internal components to their mounting points
• Replaces missing or damaged fasteners to maintain correct alignment
• Helps eliminate vibration and rattling caused by loose hardware
• Restores the original fit with OEM-matched threads and dimensions

• Disconnect power and shut off water or gas supplies before servicing
• Use the correct driver bit that matches the screw head to avoid stripping
• Replace one fastener at a time to keep parts aligned
• Tighten snugly; do not overtighten to prevent stripped threads or cracked plastic

This pivot screw secures a hinge, lever, or linkage to its bracket to create a stable pivot point. Replacing a missing or stripped screw restores proper alignment and smooth movement of the assembly.

• Fastens a pivoting component to its mounting point
• Maintains alignment and smooth, controlled motion at the pivot
• Helps prevent looseness, wobble, or sag at the joint
• Common symptoms include a missing/loose screw, binding movement, rattling, or uneven gaps

• Disconnect power; shut off gas/water if applicable before servicing
• Support the hinged or moving component to remove load from the pivot
• Remove the damaged screw and start the new screw by hand to avoid cross-threading
• Tighten snugly without over-torquing; replace companion bushings or washers if worn

This wavy spring washer applies light, consistent preload between mating parts so components stay snug and quiet. It helps control end play and vibration, supporting smoother, more reliable operation of the assembly.

• Applies axial spring tension to take up end play between parts on a shaft or fastener
• Helps resist loosening from vibration and keeps components fitting tightly
• Can address wobble, rattling, or uneven spacing when the original washer is worn or missing
• Maintains proper alignment and feel in the assembly

• Disconnect power and shut off gas/water before servicing; allow hot surfaces to cool
• Note the original stack order and position before removal; replace in the same orientation
• Seat the washer evenly and avoid over-compressing during reassembly
• Verify smooth operation and minimal play after installation

This speed control regulates power to the appliance's motor or fan, maintaining the selected speed across varying loads. Replacing a failed control restores reliable start-up, smooth speed changes, and consistent performance.

• Controls and stabilizes motor/fan speed according to the selected setting
• Modulates power for smooth acceleration and steady operation under load
• Helps resolve issues like erratic/surging speed or operating at only one speed
• Common failure symptoms: won't start, intermittent operation, or speed won't change

• Disconnect power before servicing; allow any capacitors to discharge
• Remove the appropriate cover/panel to access the control
• Tag/photograph wiring; transfer connectors one at a time to the new control
• Mount securely, keep wiring clear of moving parts, restore power, and test all speeds

This small grooved pin is a precision retaining fastener used to secure and align mating parts within an appliance assembly. Replacing a worn or missing pin restores proper support and helps the mechanism operate smoothly and quietly. What it does:

• Locks two components together with an interference-fit groove to prevent unwanted movement
• Maintains alignment of hinges, linkages, or levers in the assembly
• Reduces wobble, vibration, and rattling that can occur when a pin is worn or missing
• Common symptoms include loose or drifting parts, misalignment, intermittent operation, or unusual noises

• 1 grooved pin

• Disconnect power and, if applicable, shut off water/gas before servicing
• Support the assembly; remove any retainers, then drive out the old pin with a small punch/drift and install the new pin aligned to the original orientation
• Do not reuse damaged hardware; replace worn bushings or clips and ensure smooth movement
• Test operation before reassembling covers and restoring power

This speed selector lever is a replacement control lever that lets you choose and change a cycle's spin speed on compatible appliances, restoring proper user control and tactile feedback at the console. What it does:

• Engages the speed selector mechanism so the control responds when you change spin/speed settings
• Provides a secure grip and detent action so selections register reliably
• Replaces cracked, worn, or loose levers that won't stay in position
• Helps eliminate intermittent or unresponsive speed selection at the console

• Disconnect power to the appliance before attempting any repair.
• Use basic hand tools; access may require removing the console or control panel.
• Handle panels and clips carefully to avoid breakage; replace any damaged fasteners.

This factory fastener secures appliance components and panels in their intended positions. Replacing a missing, stripped, or corroded screw restores a tight fit, helping maintain alignment and reduce looseness and vibration-related noise.

• Fastens brackets, covers, and internal parts to the cabinet or frame
• Replace if the head is rounded, threads are worn, corroded, or the screw is missing
• Helps address rattling, buzzing, or wobbling caused by loose hardware
• Supports proper alignment of panels and assemblies

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct driver size/type to prevent stripping the head
• Start threads by hand to avoid cross-threading; do not overtighten (especially into plastic)
• Replace one-for-one in the original location and orientation